Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD)

BRAKE BOOSTER (for RHD) > REMOVAL

for Preparation Click here



1. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and setting. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C205666
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B223634
  1. Remove the screw <D>.

  1. Disengage the 2 claws and guide.

  1. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.



7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Refer to the procedure up to Remove Windshield Wiper Motor And Link Assembly .



8. REMOVE COWL BODY MOUNTING REINFORCEMENT LH


    C205554
  1. Remove the 3 bolts and cowl body mounting reinforcement LH.



9. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C205556
  1. Disengage the clamp and separate the wire harness from the outer cowl top panel sub-assembly.



    C205555E01
  1. Disengage the clamp*1 and disconnect the connector (w/ Windshield Deicer).

  1. Disengage the clamp*2 and separate the wire harness from the outer cowl top panel sub-assembly.



    C205558
  1. Disengage the claw and bend the No. 1 heater air duct splash shield seal.



    C205560
  1. Disengage the claw and bend the water guard plate RH.



    C205557
  1. Remove the 9 bolts and outer cowl top panel sub-assembly.



10. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.



11. REMOVE BRAKE PEDAL RETURN SPRING


    C205656
  1. Remove the brake pedal return spring from the brake pedal support sub-assembly and push rod pin.



12. REMOVE PUSH ROD PIN


    C205657
  1. Remove the clip and push rod pin to separate the brake pedal sub-assembly from the push rod clevis.



13. SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET


    C205563
  1. Disengage the clamp.

  1. Remove the 2 nuts and separate the brake master cylinder reservoir with bracket.



14. DISCONNECT NO. 1 RESERVOIR HOSE


    C205564E01
  1. Move the 3 clips and disconnect the No. 1 reservoir hose, No. 2 reservoir hose and No. 2 brake actuator hose.
    Text in Illustration 
    *1
    No. 1 Reservoir hose
    *2
    No. 2 Reservoir hose
    *3
    No. 2 Brake Actuator Hose



15. DISCONNECT NO. 2 RESERVOIR HOSE


16. DISCONNECT NO. 2 BRAKE ACTUATOR HOSE


17. REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET


18. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


    C205565
  1. Disengage the clamp.

  1. Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

    NOTICE:
    Be careful not to allow the brake fluid to enter the removed connector.

    HINT:
    Perform this step only when the connector has not been disconnected.



    C205567
  1. Remove the bolt and wire harness clamp bracket.



    C205652E01
  1. Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.

  1. Use tags or make a memo to identify the places to reconnect.
    Text in Illustration 
    *1
    to Front Wheel Cylinder LH
    *2
    to Rear Wheel Cylinder RH
    *3
    to Brake Booster Pump Assembly
    *4
    to Rear Wheel Cylinder LH
    *5
    to Front Wheel Cylinder RH



    C205653
  1. Using a union nut wrench, disconnect the brake line from the front flexible hose RH.

  1. Disengage the grommet and separate the brake line.



    C205659E01
  1. Remove the 4 nuts and brake booster with master cylinder assembly.
    Text in Illustration 
    *1
    Connector Portion
    *2
    Union
    *3
    Push Rod Clevis and Boot
    *4
    Front No. 2 Brake Tube

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Do not carry the brake booster with master cylinder assembly by the portion shown in the illustration.



19. REMOVE BRAKE BOOSTER GASKET