BRAKE BOOSTER (for RHD) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE REAR NO. 2 FLOOR BOARD |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 3. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 4. REMOVE REAR NO. 3 FLOOR BOARD |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 5. DISABLE BRAKE CONTROL |
Wait at least 2 minutes after the power switch off.
![]() |
Disconnect the reservoir level switch connector with the parking brake applied.
Disconnect the cable from the negative (-) battery terminal.
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal can not be further depressed.
Release the parking brake.
| 6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Remove the screw <D>.
Disengage the 2 claws and guide.
Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.
| 7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 8. REMOVE COWL BODY MOUNTING REINFORCEMENT LH |
![]() |
Remove the 3 bolts and cowl body mounting reinforcement LH.
| 9. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Disengage the clamp and separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Disengage the clamp*1 and disconnect the connector (w/ Windshield Deicer).
Disengage the clamp*2 and separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Disengage the claw and bend the No. 1 heater air duct splash shield seal.
![]() |
Disengage the claw and bend the water guard plate RH.
![]() |
Remove the 9 bolts and outer cowl top panel sub-assembly.
| 10. DRAIN BRAKE FLUID |
| 11. REMOVE BRAKE PEDAL RETURN SPRING |
![]() |
Remove the brake pedal return spring from the brake pedal support assembly and push rod pin.
| 12. REMOVE PUSH ROD PIN |
![]() |
Remove the clip and push rod pin to separate the brake pedal support assembly from the push rod clevis.
| 13. SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET |
![]() |
Disengage the clamp.
Remove the 2 nuts and separate the brake master cylinder reservoir with bracket.
| 14. DISCONNECT NO. 1 RESERVOIR HOSE |
![]() |
Move the 3 clips and disconnect the No. 1 reservoir hose, No. 2 reservoir hose and No. 2 brake actuator hose.
| *1 | No. 1 Reservoir hose |
| *2 | No. 2 Reservoir hose |
| *3 | No. 2 Brake Actuator Hose |
| 15. DISCONNECT NO. 2 RESERVOIR HOSE |
| 16. DISCONNECT NO. 2 BRAKE ACTUATOR HOSE |
| 17. REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET |
| 18. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
![]() |
Disengage the clamp.
Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.
![]() |
Remove the bolt and wire harness clamp bracket.
![]() |
Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.
Use tags or make a memo to identify the places to reconnect.
| *1 | to Front Wheel Cylinder LH |
| *2 | to Rear Wheel Cylinder RH |
| *3 | to Brake Booster Pump Assembly |
| *4 | to Rear Wheel Cylinder LH |
| *5 | to Front Wheel Cylinder RH |
![]() |
Using a union nut wrench, disconnect the brake line from the front flexible hose RH.
Disengage the grommet and separate the brake line.
![]() |
Remove the 4 nuts and brake booster with master cylinder assembly.
| *1 | Connector Portion |
| *2 | Union |
| *3 | Push Rod Clevis and Boot |
| *4 | Front No. 2 Brake Tube |
| 19. REMOVE BRAKE BOOSTER GASKET |