ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL FLYWHEEL SUB-ASSEMBLY |
Gently place the engine assembly onto wood blocks or equivalent.
Install the flywheel sub-assembly .
| 2. INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY |
Gently place the engine assembly onto wood blocks or equivalent.
Install the transmission input damper assembly .
| 3. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY |
Install the hybrid vehicle transaxle assembly .
| 4. INSTALL ENGINE WIRE |
| 5. INSTALL FLYWHEEL HOUSING SIDE COVER |
![]() |
Install the flywheel housing side cover.
| 6. INSTALL STARTER HOLE INSULATOR |
![]() |
Install the starter hole insulator with the 2 bolts.
| 7. INSTALL RADIATOR PIPE |
![]() |
Install the radiator pipe with the 2 bolts.
Install the No. 3 radiator hose with the clamp.
| 8. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
![]() |
Position the engine mounting insulator sub-assembly RH as shown in the illustration.
Temporarily install bolt A to the engine mounting insulator sub-assembly RH.
Tighten the 3 bolts to the engine mounting insulator sub-assembly RH in the order the bolt B, bolt C and bolt A.
Install the 2 cooler brackets with the 2 bolts.
| 9. INSTALL ENGINE MOUNTING INSULATOR LH |
![]() |
Temporarily install bolt A to the engine mounting insulator LH.
Tighten the 4 bolts to the engine mounting insulator LH in the order the bolt C, bolt B, bolt D and bolt A.
| 10. INSTALL REAR ENGINE MOUNTING INSULATOR |
![]() |
Install the rear engine mounting insulator to the engine mounting bracket with the through bolt.
| 11. INSTALL FRONT ENGINE MOUNTING INSULATOR |
![]() |
Temporarily install the front engine mounting insulator with the bolt and nut.
| 12. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
Set the engine assembly with transaxle on the engine lifter.
![]() |
Remove the 2 bolts and 2 engine hangers.
![]() |
Set the engine assembly with transaxle and front suspension crossmember on the engine lifter.
Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulators RH and LH can be installed.
![]() |
Install the front crossmember with the 4 bolts.
![]() |
Install the front engine mounting insulator to the front crossmember with the 2 bolts.
![]() |
Install the engine mounting insulator LH with the through bolt and nut.
![]() |
Install the engine mounting insulator RH with the bolt and 2 nuts.
![]() |
Tighten the front engine mounting insulator with the bolt and nut.
| 13. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Support the front suspension crossmember with a transmission jack.
While inserting SST into the reference holes on the front suspension crossmember RH and LH alternately, tighten 2 bolts A, 2 bolts B, C and 2 nuts on the RH and LH sides to the respective specified torque in several steps.

![]() |
Install the 2 wire harness clamp brackets with the 2 bolts.
| 14. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH |
![]() |
Install the front suspension member rear brace LH with the 2 bolts B and bolt A.
| 15. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH |
| 16. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
![]() |
Install the rear side rail reinforcement sub-assembly LH with the 4 bolts.
| 17. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH |
![]() |
Install the rear side rail reinforcement sub-assembly RH with the 4 bolts.
| 18. INSTALL FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT |
![]() |
Install the front engine mounting bracket lower reinforcement with the 2 bolts.
| 19. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH |
Install a new front drive shaft hole snap ring to the front drive inboard joint assembly.
| 20. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH |
| 21. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly.
![]() |
Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
| *1 | Matchmark |
| 22. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
| 23. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Install the front No. 1 lower suspension arm sub-assembly to the front lower ball joint with the bolt and 2 nuts.
| 24. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH |
| 25. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Install the front stabilizer link assembly to the front shock absorber with coil spring with the nut.
| 26. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 27. CONNECT TIE ROD END SUB-ASSEMBLY LH |
![]() |
Connect the tie rod end sub-assembly LH to the steering knuckle with the nut.
Install a new clip.
| 28. CONNECT TIE ROD END SUB-ASSEMBLY RH |
| 29. INSTALL FRONT SPEED SENSOR LH |
![]() |
Install the front speed sensor and front flexible hose to the front shock absorber with the bolt and clamp.
| 30. INSTALL FRONT SPEED SENSOR RH |
| 31. INSTALL FRONT AXLE SHAFT NUT LH |
Clean the threaded parts on the drive shaft and a new axle shaft nut using a non-residue solvent.
![]() |
Using a socket wrench (30 mm), install the axle shaft nut.
Using a chisel and hammer, stake the front axle shaft nut.
| 32. INSTALL FRONT AXLE SHAFT NUT RH |
| 33. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System) |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 41.5 mm (1.64 in.) |
Fully insert a new gasket to the exhaust manifold.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold.
| *1 | Exhaust Manifold |
| *2 | Gasket |
| *3 | Wooden Block |
Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.
![]() |
Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.
![]() |
Connect the 2 heater water hoses.
| 34. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System) |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 41.5 mm (1.64 in.) |
Fully insert a new gasket to the exhaust manifold.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold.
| *1 | Exhaust Manifold |
| *2 | Gasket |
| *3 | Wooden Block |
Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.
![]() |
Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.
| 35. INSTALL FRONT CENTER FLOOR BRACE |
![]() |
Install the front center floor brace with the 4 bolts.
| 36. INSTALL FRONT NO. 3 ENGINE UNDER COVER |
![]() |
Install the front No. 3 engine under cover with the 4 clips.
| 37. INSTALL TAIL EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 38.5 mm (1.52 in.) |
Fully insert a new gasket to the front exhaust pipe assembly.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the front exhaust pipe assembly.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Gasket |
| *3 | Wooden Block |
Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.
![]() |
Install the tail exhaust pipe assembly with the 2 bolts and 2 compression springs.
| 38. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.
| *1 | Clip A |
| *2 | Clip B |
| 39. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.
| *1 | Matchmark |
Install the bolt.
| 40. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 41. INSTALL WIRE HARNESS |
![]() |
Connect the wire harness with the 2 clamps.
![]() |
Install the wire harness with the bolt.
![]() |
Connect the wire harness with the 3 clamps.
![]() |
Connect the wire harness to the engine room junction block.
Connect the 2 connectors to the engine room junction block.
![]() |
Connect the connector to the ECM with the 2 clamps and lock lever.
| 42. INSTALL ELECTRIC INVERTER COMPRESSOR |
![]() |
Temporarily install the electric inverter compressor with the 3 bolts.
![]() |
Install the electric inverter compressor with the 3 bolts.
![]() |
Connect the connector <B>.
| *1 | Green-colored Lock |
Connect the connector <A> and slide the green-colored lock in the direction indicated by the arrow in the illustration to lock it securely.
| 43. CONNECT FUEL TUBE SUB-ASSEMBLY |
Connect the fuel tube connector and fuel pipe.
![]() |
Engage the claw and install the No. 1 fuel pipe clamp.
| 44. CONNECT NO. 1 FUEL VAPOR FEED HOSE |
![]() |
Connect the No. 1 fuel vapor feed hose with the clamp.
| 45. CONNECT HEATER HOSE |
![]() |
Connect the heater hose with the clamp.
| 46. CONNECT INLET HEATER WATER HOSE |
![]() |
Connect the inlet heater water hose with the clamp.
| 47. CONNECT OUTLET HEATER WATER HOSE |
![]() |
Connect the outlet heater water hose with the clamp.
| 48. CONNECT NO. 5 INVERTER COOLING HOSE |
![]() |
Connect the No. 5 inverter cooling hose with the clamp.
| 49. CONNECT NO. 3 INVERTER COOLING HOSE |
![]() |
Connect the No. 3 inverter cooling hose with the clamp.
| 50. CONNECT NO. 4 WATER BY-PASS HOSE |
![]() |
Connect the No. 4 water by-pass hose with the clamp.
| 51. CONNECT NO. 2 RADIATOR HOSE |
![]() |
Connect the No. 2 radiator hose with the clamp.
| 52. CONNECT NO. 1 RADIATOR HOSE |
![]() |
Connect the No. 1 radiator hose with the clamp.
| 53. INSTALL INVERTER TRAY BRACKET |
![]() |
Position the inverter tray bracket as shown in the illustration.
Temporarily install bolt B to the inverter tray bracket.
Tighten the 5 bolts to the inverter tray bracket in the order the bolt A, bolt C, bolt D, bolt E and bolt B.
Connect the 2 clamps to the inverter tray bracket.
| 54. INSTALL INVERTER RESERVE TANK ASSEMBLY |
![]() |
Temporarily install bolt A to the inverter reserve tank assembly.
Tighten the 2 bolts to the inverter reserve tank assembly in the order the bolt B and bolt A.
| 55. INSTALL INVERTER WITH CONVERTER ASSEMBLY |
![]() |
Temporarily install the inverter with converter assembly with the 3 bolts.
Tighten the bolt A.
Tighten the 2 bolts.
| 56. CONNECT WATER HOSE |
![]() |
Connect the water hose to the inverter with converter assembly and lock the hose with the retainer.
![]() |
Connect the water hose to the inverter with converter assembly and lock the hose with the retainer.
| 57. CONNECT NO. 2 ENGINE ROOM WIRE |
![]() |
Disconnect the No. 2 engine room wire from the protector.
![]() |
Connect the No. 2 engine room wire with the bolt and 2 claws.
![]() |
Install the No. 1 relay block cover and 2 clamps.
Install the relay block cover.
| 58. REMOVE INVERTER TERMINAL COVER |
![]() |
Remove the 9 bolts and inverter terminal cover.
| 59. CONNECT NO. 2 ENGINE WIRE |
![]() |
Connect the No. 2 engine wire (high voltage cables of the air conditioning) with the 4 bolts to the inverter with converter assembly.
![]() |
Connect the harness clamp.
| 60. CONNECT HIGH VOLTAGE CABLE OF FRONT TRANSAXLE |
![]() |
Connect the high voltage cable of the motor (MG2) with 5 bolts to the inverter with converter assembly.
![]() |
Connect the harness clamp.
![]() |
Connect the high voltage cable of the generator (MG1) with the 5 bolts to the inverter with converter assembly.
![]() |
Install the cable and cover.
| *1 | Align Mark |
| 61. CONNECT FRAME WIRE |
![]() |
Connect the frame wire (high voltage cables of the hybrid battery) with the 4 bolts to the inverter with converter assembly.
| *1 | Front view of frame wire connector |
| *2 | Interlock |
| *3 | High voltage cables of the hybrid battery |
![]() |
Connect the harness clamp.
| 62. CHECK HIGH VOLTAGE CABLE CONNECTION |
![]() |
Check that each connector and terminal is firmly installed.
| 63. INSTALL INVERTER TERMINAL COVER |
![]() |
Install the inverter terminal cover with the 9 bolts to the inverter with converter assembly.
| *1 | Interlock |
| 64. CONNECT ENGINE ROOM MAIN WIRE |
![]() |
Install the bolt, clamp and clip, and connect the engine room main ware.
![]() |
Install the bolt.
![]() |
Connect the engine wire to the engine room main wire.
![]() |
Connect the connector to the inverter with converter assembly and lock the connector with the lock lever.
| 65. INSTALL NO. 1 INVERTER BRACKET |
![]() |
Temporarily install the No. 1 inverter bracket with the 3 bolts.
Tighten the 3 bolts in the order shown in the illustration.
| 66. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose assembly and lock the hose clamp.
Connect the ventilation hose.
| 67. INSTALL AIR CLEANER CASE |
![]() |
Install the air cleaner case with the 3 bolts.
Connect the No. 4 water by-pass hose to the air cleaner case with the 3 clamps.
Install the air cleaner filter element.
| 68. INSTALL INLET AIR CLEANER ASSEMBLY |
![]() |
Install the inlet air cleaner assembly with the 3 bolts.
Connect the wire harness clamp to the inlet air cleaner assembly.
Connect the No. 4 water by-pass hose to the inlet air cleaner assembly with the clamp.
| 69. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly with the 2 clamps and hose band.
Connect the air flow meter connector.
| 70. INSTALL SERVICE PLUG GRIP |
Wear insulated gloves and install the service plug grip in the order shown in the illustration.

Rotate the handle of the service plug grip 90° toward the battery and slide it in the direction shown by the arrow until a click sound is heard.
| 71. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 72. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 73. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 74. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 75. ADD HYBRID TRANSAXLE FLUID |
![]() |
Add transaxle fluid until the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening.
| *1 | Filler Plug |
| *2 | Filler Nozzle |
After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the fluid is insufficient, return to the Add Hybrid Transaxle Fluid procedure.)
Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.
| 76. INSPECT HYBRID TRANSAXLE FLUID |
![]() |
Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
| *1 | Filler Plug |
Check that the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the fluid is insufficient, return to the Add Hybrid Transaxle Fluid procedure.)
Check for leaks if the quantity of transaxle fluid is low.
Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.
| 77. ADD COOLANT (for Engine) |
Tighten the radiator drain cock plug.
Tighten the cylinder block drain cock plug.
Remove the reservoir tank cap.
Connect the hose to the air release valve.
Loosen the air release valve.
Add TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank filler opening until coolant overflows from the air release valve. Then tighten the air release valve.
| Item | Capacity |
| Engine coolant | w/ Exhaust Heat Recirculation System: 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
| w/o Exhaust Heat Recirculation System: 6.5 liters (6.8 US qts, 5.7 lmp. qts) |
Disconnect the hose from the air release valve.
![]() |
Add coolant to B line of the reservoir tank.
| *1 | B Line |
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Put the engine in inspection mode (Click here).
Install the reservoir tank cap and air release valve, and warm up the engine sufficiently.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
![]() |
After the engine has cooled down, check that the coolant level is between full and low.
| *1 | Full Line |
| *2 | Low Line |
| 78. ADD COOLANT (for Inverter) |
| DTC Code | Detection Item |
| P0A01-726 | Motor Electronics Coolant Temperature Sensor Circuit Range / Performance |
| P0A04-725 | Motor Electronics Coolant Temperature Sensor Circuit Intermittent |
| P0A08-264 | DC / DC Converter Status Circuit |
| P0A78-284 | Drive Motor "A" Inverter Performance |
| P0A78-286 | Drive Motor "A" Inverter Performance |
| P0A7A-322 | Generator Inverter Performance |
| P0A7A-324 | Generator Inverter Performance |
| P0A93-346 | Inverter Cooling System Performance |
| P0A94-553 | DC / DC Converter Performance |
| P0A94-557 | DC / DC Converter Performance |
| P0AEE-277 | Motor Inverter Temperature Sensor "A" Circuit Range / Performance |
| P0AF1-276 | Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic |
| P0BCD-315 | Generator Inverter Temperature Sensor Circuit Range / Performance |
| P0BD0-314 | Generator Inverter Temperature Sensor Circuit Intermittent / Erratic |
| P0C39-626 | DC / DC Converter Temperature Sensor "A" Range / Performance |
| P0C3C-625 | DC / DC Converter Temperature Sensor "A" Intermittent / Erratic |
| P0C3E-628 | DC / DC Converter Temperature Sensor "B" Range / Performance |
| P0C41-627 | DC / DC Converter Temperature Sensor "B" Intermittent / Erratic |
| P0C73-776 | Motor Electronics Coolant Pump "A" Control Performance |
![]() |
Slowly pour coolant into the reserve tank until it reaches the F line.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
On the intelligent tester, enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Keep the coolant at the F line in the reserve tank to compensate for the drop in coolant level when the air bleeds.
When not using the intelligent tester:
Turn the power switch on (READY). [*1]
Turn the power switch off and add coolant to the F line because the coolant level drops as the air bleeds. [*2]
Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.
After the air is completely bled from the cooling system, tighten the reserve tank cap.
![]() |
Add coolant to the F line of the reserve tank.
| 79. ADD ENGINE OIL |
Add new engine oil and install the oil filler cap.
| Oil Grade | Oil Viscosity (SAE) |
|
|
| API grade SL or SM multigrade engine oil |
|
| Item | Standard Condition |
| Drain and refill with oil filter change | 4.2 liters (4.4 US qts, 3.7 lmp. qts) |
| Drain and refill without oil filter change | 3.9 liters (4.1 US qts, 3.4 lmp. qts) |
| Dry fill | 4.7 liters (5.0 US qts, 4.1 lmp. qts) |
| 80. INSPECT ENGINE OIL LEVEL |
Put the engine in inspection mode (Click here).
Warm up and stop the engine, then wait for 5 minutes. The oil level should be between the low level and full level marks on the engine oil level dipstick. If the engine oil level is low, check for leakage and add oil up to the full level mark.
| 81. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there is no fuel leakage after performing maintenance anywhere on the fuel system. If there is a fuel leak, repair or replace parts as necessary.
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
| 82. INSPECT FOR COOLANT LEAK (for Engine) |
Remove the reservoir tank cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
Remove the radiator cap tester.
Install the reservoir tank cap.
| 83. INSPECT FOR COOLANT LEAK (for Inverter) |
Remove the reserve tank cap.
![]() |
Install the radiator cap tester.
Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 17.7 psi), and then check that the pressure does not drop.
Reinstall the reserve tank cap.
| 84. INSPECT FOR OIL LEAK |
| 85. INSPECT FOR EXHAUST GAS LEAK |
| 86. INSTALL NO. 2 ENGINE UNDER COVER |
| 87. INSTALL NO. 1 ENGINE UNDER COVER |
| 88. INSTALL ENGINE UNDER COVER |
| 89. INSTALL FRONT SPOILER COVER (w/ Front Spoiler) |
| 90. INSTALL REAR ENGINE UNDER COVER LH |
| 91. INSTALL REAR ENGINE UNDER COVER RH |
| 92. INSTALL FRONT WHEELS |
| 93. INSPECT IGNITION TIMING |
Put the engine in inspection mode (Click here).
Warm up and stop the engine.
When using the intelligent tester:
Check the ignition timing.
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (Click here).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
Enter the following menus: Connect the TC and TE1 / OFF.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Remove the No. 2 cylinder head cover .
![]() |
Pull out the wire harness shown in the illustration.
Connect the clip of the timing light to the wire harness.
Inspect the ignition timing at idle.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing at idle.
Confirm that the ignition timing advances when the engine rpm is increased.
Remove the timing light.
Install the No. 2 cylinder head cover .
| 94. INSPECT ENGINE IDLE SPEED |
Put the engine in inspection mode (Click here).
Warm up and stop the engine.
Connect the intelligent tester to the DLC3.
Put the engine in inspection mode (Click here).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Inspect the engine idle speed.
Turn the power switch off.
Turn the intelligent tester off.
Disconnect the intelligent tester from the DLC3.
| 95. INSPECT CO/HC |
Put the engine in inspection mode (Click here).
Warm up the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.
Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.
Check the DTCs (Click here).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problem | Possible Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 96. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 97. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Engage the 3 clips to install the cover.
| 98. INSTALL RADIATOR SUPPORT OPENING COVER |
![]() |
Engage the 2 claws and install the radiator support opening cover.
Install the 3 clips.
| 99. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Install the outer cowl top panel sub-assembly with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp to install the wire harness.
| 100. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Install the outer cowl top panel with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp*2 of the wire harness.
Engage the clamp*1 and connect the connector (w/ Windshield Deicer).
![]() |
Engage the clamp of the wire harness.
| 101. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 102. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 103. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Engage the grommet as shown in the illustration.
| *1 | Grommet |
Install the windshield wiper motor and link assembly with the 2 bolts.
Connect the connector.
| 104. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
Engage the 8 guides <B>.

Engage the 5 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.
![]() |
Install the 2 clips.
| 105. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
Engage the 8 guides <B>.

Engage the 6 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.
![]() |
Install the 2 clips.
| 106. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Engage the guide <B> as shown in the illustration.
Engage the claw and guide <A> to install the cowl side ventilator sub-assembly LH as shown in the illustration.
| 107. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 108. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
When reusing the front wiper arm and blade assembly RH:
Clean the wiper arm serrations.
| *1 | Wiper Arm Serration |
| *2 | Wire Brush |
| *3 | Wiper Pivot Serration |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| *1 | Ceramic Dot |
| 109. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
When reusing the front wiper arm and blade assembly LH:
Clean the wiper arm serrations.
| *1 | Wiper Arm Serration |
| *2 | Wire Brush |
| *3 | Wiper Pivot Serration |
When reusing the windshield wiper link assembly:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| *1 | Ceramic Dot |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.
| 110. INSTALL FRONT WIPER ARM HEAD CAP |
![]() |
Engage the 3 claws to install the front wiper arm head cap.
| 111. CHECK ABS SPEED SENSOR SIGNAL |