CYLINDER BLOCK > REASSEMBLY |
| 1. INSTALL STUD BOLT |
![]() |
Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.
| *a | LH Side |
| 2. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm socket hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.
| 3. INSTALL PISTON |
![]() |
Using a screwdriver, install a new snap ring at one end of the piston pin hole.
| *1 | Pin Hole Cutout Portion |
Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).
![]() |
Align the front marks of the piston and connecting rod sub-assembly, insert the connecting rod sub-assembly into the piston, and then push in the piston pin with your thumb until it comes into contact with the snap ring.
| *a | Front Mark |
Using a screwdriver, install a new snap ring on the other end of the piston pin hole.
![]() |
Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
| 4. INSTALL PISTON RING SET |
![]() |
Install the oil ring expander and oil ring by hand.
| *1 | Oil Ring Expander |
| *2 | Oil Ring |
| *3 | Coil Joint |
| *4 | Oil Ring End |
Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.

| *A | w/ EGR System | *B | w/o EGR System |
| *1 | No. 1 Compression Ring | *2 | No. 2 Compression Ring |
| *3 | Piston Ring Expander | - | - |
| *a | Code Mark (1R) | *b | Code Mark (2R) |
| *c | Code Mark (T1) | *d | Code Mark (2T) |
| *e | Paint Mark | - | - |
![]() | Upward | - | - |
![]() |
Position the piston rings so that the ring ends are as shown in the illustration.
| *1 | No. 1 Compression Ring and Oil Ring |
| *2 | No. 2 Compression Ring and Oil Ring Expander |
![]() | Engine Front |
| 5. INSTALL CRANKSHAFT BEARING |
![]() |
Install the upper bearing (except No. 3 journal).
| *1 | Vernier Caliper |
Install the upper bearing to the cylinder block.
Using a vernier caliper, measure the distance between the cylinder block edge and the upper bearing edge.
![]() |
Install the upper bearing (for No. 3 journal).
| *1 | Vernier Caliper |
Install the upper bearing to the cylinder block.
Using a vernier caliper, measure the distance between the cylinder block edge and the upper bearing edge.
Install the lower bearing.
Install the upper bearing to the cylinder block.
![]() |
Using a vernier caliper, measure the distance between the bearing cap edge and the lower bearing edge.
| *1 | Vernier Caliper |
| *a | Mark 1, 2, 3, 4 or 5 |
| 6. INSTALL UPPER CRANKSHAFT THRUST WASHER |
![]() |
Install the 2 upper crankshaft thrust washers to the No. 3 journal position of the cylinder block with the oil grooves facing outward.
| *1 | Oil Groove |
Apply engine oil to the upper crankshaft thrust washer.
| 7. INSTALL CRANKSHAFT |
Apply engine oil to the upper bearings and install the crankshaft to the cylinder block.
Apply engine oil to the lower bearings.
![]() |
Check the number marks and install the bearing caps to the cylinder block.
| *a | Number Mark |
![]() | Engine Front |
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Temporarily install the 10 crankshaft bearing cap bolts.
![]() |
Push on the crankshaft bearing caps with your hand until the clearance between the crankshaft bearing caps and cylinder block is less than 5 mm (0.197 in.).
![]() |
Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.
Install the crankshaft bearing cap bolts.
Step 1:
![]() |
Install and uniformly tighten the 10 crankshaft bearing cap bolts in the sequence shown in the illustration.
Step 2:
![]() |
Mark the front of the bearing cap bolts with paint.
| *a | Paint Mark |
![]() | Engine Front |
Tighten the bearing cap bolts 90° in the sequence shown in step 1.
Check that the paint marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Check the crankshaft thrust clearance .
| 8. INSTALL CONNECTING ROD BEARING |
Install the connecting rod bearings to the connecting rod sub-assemblies and connecting rod caps.
![]() |
Using a vernier caliper, measure the distance between the edges of the connecting rod sub-assemblies and connecting rod cap bearings, and the connecting rod caps and the connecting rod bearings.
| *1 | Vernier caliper |
| 9. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
![]() |
Apply engine oil to the cylinder walls, pistons, and the surfaces of the connecting rod bearings.
| *1 | No. 1 Compression Ring and Oil Ring |
| *2 | No. 2 Compression Ring and Oil Ring Expander |
![]() | Engine Front |
Position the piston rings so that the ring ends are as shown in the illustration.
![]() |
Using a piston ring compressor, push the correctly numbered piston and connecting rod sub-assembly into the cylinder with the front mark of the piston facing forward.
| *a | Front Mark |
![]() |
Check that the front mark of the connecting rod cap is facing in the correct direction.
| *a | Front Mark |
Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.
Install the connecting rod cap bolts.
Step 1:
![]() |
Using SST, install and alternately tighten the bolts of the connecting rod cap in several steps.
Step 2:
![]() |
Mark the front of the connecting rod cap bolts with paint.
| *a | Paint Mark |
![]() | Engine Front |
Tighten the cap bolts 90° as shown in the illustration.
Check that the crankshaft turns smoothly.
Check the connecting rod thrust clearance .
| 10. INSTALL NO. 1 VENTILATION CASE |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal Packing |
| *b | Seal Packing Diameter |
| Seal Packing Diameter | Distance from inside edge of cover to center of seal packing |
| 2.0 to 3.0 mm (0.0787 to 0.118 in.) | 3.0 mm (0.118 in.) |
Type A:
![]() |
Install the ventilation case with the 6 bolts and 2 nuts.
Type B:
![]() |
Install the ventilation case with the 8 bolts.