REAR SEAT ASSEMBLY > REASSEMBLY |
| 1. INSTALL BENCH TYPE REAR SEAT CUSHION COVER |
Using hog ring pliers, install the rear seat cushion cover with 14 new hog rings.

Using hog ring pliers, install the rear seat cushion cover with 28 new hog rings.

| 2. INSTALL REAR SEATBACK LOCK ASSEMBLY LH |
![]() |
Install the rear seatback lock assembly LH with the 2 bolts.
| 3. INSTALL REAR SEATBACK LOCK RELEASE BUTTON LH |
![]() |
Install the rear seatback lock release button LH to the rear seatback frame LH as shown in the illustration.
| 4. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH |
![]() |
Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 9 new hog rings.
| 5. INSTALL REAR SEATBACK COVER WITH PAD LH |
Temporarily install the rear seatback cover with pad LH to the rear seatback frame sub-assembly LH.
![]() |
Engage the 4 claws and install the 2 rear seat headrest supports.
![]() |
Using hog ring pliers, install 13 new hog rings.
![]() |
Engage the 6 clips and Install the rear seatback cover with pad LH with the 2 clips.
| 6. INSTALL REAR SEATBACK STOP BUTTON GROMMET |
![]() |
Engage the 3 claws and install the rear seatback stop button grommet.
| 7. INSTALL REAR SEAT SHOULDER BELT GUIDE LH |
![]() |
Engage the guide and install the rear seat shoulder belt guide LH with the 2 screws.
| 8. INSTALL REAR SEATBACK COVER LH |
![]() |
Engage the 4 claws and install the rear seatback cover LH.
| 9. INSTALL REAR SEATBACK LOCK ASSEMBLY RH |
![]() |
Install the rear seatback lock assembly RH with 2 bolts.
| 10. INSTALL REAR SEATBACK LOCK RELEASE BUTTON RH |
![]() |
Install the rear seatback lock release button RH to the rear seatback frame RH as shown in the illustration.
| 11. INSTALL REAR CENTER SEAT BELT ASSEMBLY |
![]() |
Install the rear center seat belt assembly with the nut.
| *1 | Protruding Part |
| 12. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH |
Temporarily install the separate type rear seatback cover RH.
![]() |
Using hog ring pliers, install 9 new hog rings.
![]() |
Using hog ring pliers, install the rear seatback cover with pad RH with 7 new hog rings.
Install the rear seatback cover with pad RH.
| 13. INSTALL REAR SEATBACK COVER WITH PAD RH |
Temporarily install the rear seatback cover with pad RH.
![]() |
Engage the 4 claws and install the 2 rear seat headrest supports.
![]() |
Engage the 4 claws and install the 2 rear seat center headrest supports.
![]() |
Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to engage the 2 claws (A).
Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to disengage the 2 claws (B) and remove the cover.
![]() |
Engage the 2 claws and install the seat belt anchor cover cap.
![]() |
Using hog ring pliers, install 16 new hog rings.
![]() |
Engage the 6 clips and Install the rear seatback cover with pad RH with the 3 clips.
| 14. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY |
![]() |
Install the bush.
![]() |
Insert the pin into the rear seatback.
Install the rear seat center armrest assembly with the bolt and bush.
| 15. INSTALL CENTER ARMREST HINGE COVER |
![]() |
Engage the claw and install the center armrest hinge cover as shown in the illustration.
| 16. INSTALL REAR SEATBACK STOP BUTTON GROMMET |
![]() |
Engage the 3 claws and install the rear seatback stop button grommet.
| 17. INSTALL REAR SEAT SHOULDER BELT GUIDE RH |
![]() |
Engage the guide and install the rear seat shoulder belt guide RH with the 2 screws.
| 18. INSTALL REAR SEATBACK COVER RH |
![]() |
Engage the 4 claws and install the rear seatback cover RH.
| 19. INSTALL REAR SEATBACK CENTER COVER (for LHD) |
![]() |
Engage the 4 claws and install the rear seatback center cover.