Home › Steering › STEERING COLUMN › STEERING WHEEL

STEERING WHEEL > INSTALLATION

for Preparation Click here



1. INSTALL LOWER STEERING WHEEL BOSS COVER


    C206252
  1. Engage the 2 pins and 4 claws to install the lower steering wheel boss cover to the steering wheel sub-assembly.



2. INSTALL CRUISE CONTROL SWITCH WIRE


3. INSTALL CRUISE CONTROL MAIN SWITCH


    E186305
  1. Install the cruise control main switch with the 2 screws.



    E186306
  1. Connect the connector.



4. INSTALL STEERING PAD SWITCH ASSEMBLY


    C206250
  1. Engage the 2 claws to install the steering pad switch assembly (RH side) to the steering wheel sub-assembly.

  1. Install the 2 screws.

    Torque:
    2.4 N*m{ 25 kgf*cm , 21 in.*lbf }



    C206251
  1. Engage the 2 claws to install the steering pad switch assembly (LH side) to the steering wheel sub-assembly.

  1. Install the 2 screws.

    Torque:
    2.4 N*m{ 25 kgf*cm , 21 in.*lbf }



5. INSTALL STEERING SHAKE DAMPER


    C206249
  1. Install the steering shake damper to the steering wheel assembly with the 2 screws.

    Torque:
    2.4 N*m{ 25 kgf*cm , 21 in.*lbf }



6. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


7. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B231042
  1. Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.



    B231043E01
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
    Text in Illustration 
    *1
    Alignment Mark

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



8. INSTALL STEERING WHEEL ASSEMBLY


    C206245E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft.
    Text in Illustration 
    *1
    Matchmark

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



9. INSTALL STEERING PAD

HINT:
Refer to the instructions for Installation of the steering pad (Click here).



10. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



13. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



14. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



15. INSPECT STEERING PAD


    B226975
  1. Visually check for defects with the steering pad installed on the vehicle.

    1. The defects are as follows:

      1. Cuts on the surface and in the grooves of the steering pad
      2. Small cracks on the surface and in the grooves of the steering pad
      3. Significant discoloration on the surface and in the grooves of the steering pad

      OK:
      No defects are found.

      HINT:
      If any of the defects is found, replace the steering pad with a new one.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



16. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).