Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

DTC    B2430    LED Headlight LH Circuit Malfunction

DTC    B2431    LED Headlight RH Circuit Malfunction

for Preparation Click here


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a malfunction is detected in the communication between the headlight assembly and main body ECU (multiplex network body ECU).

DTC No.
DTC Detection Condition
Trouble Area
B2430
LED headlight LH circuit malfunction
  1. Light control ECU LH
  2. Headlight unit LH
  3. Integration relay
  4. Harness or connector
  5. Main body ECU (multiplex network body ECU)
B2431
LED headlight RH circuit malfunction
  1. Light control ECU RH
  2. Headlight unit RH
  3. Integration relay
  4. Harness or connector
  5. Main body ECU (multiplex network body ECU)

WIRING DIAGRAM


E190935E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    Both DTC B2430 and B2431 are not output.
    A
    Both DTC B2430 and B2431 are output.
    B
    DTC B2430 or B2431 is output.
    C



B
Go to step 2

C
Go to step 6
A

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BATTERY AND BODY GROUND)


    E181517E03
  1. Disconnect the 1H integration relay connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connector
    Condition
    Specified Condition
    1H-7 (BATT) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1H-3 (GND2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)



    E190922E01
  1. Disconnect the 1G integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1G-22 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 1G integration relay connector.

  1. Disconnect the 2C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1G-9 (HL4) - 2C-32
    Always
    Below 1 Ω
    1G-9 (HL4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E182506E06
  1. Remove the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-32 - A-15 (HRLY)
    Always
    Below 1 Ω
    2C-32 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


5.REPLACE INTEGRATION NO.1 RELAY
  1. Temporarily replace the integration relay with a new or normally functioning one (Click here).

  1. Check for DTC (Click here).

    OK:
    DTC B2430 and B2431 are not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END 

6.INSPECT HEADLIGHT ASSEMBLY


    E190924E04
  1. Disconnect the A10 or A39 headlight assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    LH Side (B2430) 
    Tester Connection
    Switch Condition
    Specified Condition
    A10-3 (LO) - Body ground
    Light control switch in head position
    11 to 14 V
    RH Side (B2431) 
    Tester Connection
    Switch Condition
    Specified Condition
    A39-3 (LO) - Body ground
    Light control switch in head position
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Headlight Assembly LH)
    *2
    Front view of wire harness connector
    (to Headlight Assembly RH)



NG
Go to step 10
OK


7.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    E190924E06
  1. Disconnect the A10 or A39 headlight assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    LH Side (B2430) 
    Tester Connection
    Switch Condition
    Specified Condition
    A10-2 (IN2) - Body ground
    Power switch on (IG) and light control switch in head position
    11 to 14 V
    RH Side (B2431) 
    Tester Connection
    Switch Condition
    Specified Condition
    A39-2 (IN1) - Body ground
    Power switch on (IG) and light control switch in head position
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Headlight Assembly LH)
    *2
    Front view of wire harness connector
    (to Headlight Assembly RH)



NG
Go to step 11
OK


8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)


    E190924E07
  1. Disconnect the A10 or A39 headlight assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side (B2430) 
    Tester Connection
    Condition
    Specified Condition
    A10-1 (E) - Body ground
    Always
    Below 1 Ω
    RH Side (B2431) 
    Tester Connection
    Condition
    Specified Condition
    A39-1 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Headlight Assembly LH)
    *2
    Front view of wire harness connector
    (to Headlight Assembly RH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE LIGHT CONTROL ECU
  1. Temporarily replace the headlight control ECU with a new or normally functioning one (Click here).

  1. Check for DTC (Click here).

    OK:
    DTC B2430 or B2431 is not output.



NG
REPLACE HEADLIGHT UNIT (Click here)
OK

END 

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - POWER DISTRIBUTOR)
  1. Disconnect the 1G integration relay connector.

  1. Disconnect the A10 or A39 headlight assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side (B2430) 
    Tester Connection
    Condition
    Specified Condition
    1G-2 (HLPL) - A10-3 (LO)
    Always
    Below 1 Ω
    1G-2 (HLPL) - Body ground
    Always
    10 kΩ or higher
    RH Side (B2431) 
    Tester Connection
    Condition
    Specified Condition
    1G-1 (HLPR) - A39-3 (LO)
    Always
    Below 1 Ω
    1G-1 (HLPR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INTEGRATION NO.1 RELAY (Click here)  

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY)
  1. Disconnect the L8 main body ECU (multiplex network body ECU) connector.

  1. Disconnect the A10 or A39 headlight assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side (B2430) 
    Tester Connection
    Condition
    Specified Condition
    L8-21 (LLEW) - A10-2 (IN2)
    Always
    Below 1 Ω
    L8-21 (LLEW) - Body ground
    Always
    10 kΩ or higher
    RH Side (B2431) 
    Tester Connection
    Condition
    Specified Condition
    L8-5 (RLEW) - A39-2 (IN1)
    Always
    Below 1 Ω
    L8-5 (RLEW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)