FRONT DOOR BELT MOULDING > INSTALLATION |
| 1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 7 claws to install the front door belt moulding assembly.
| 2. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
w/ Navigation System for HDD:
Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the grommet.
Connect the cable to the negative (-) battery terminal.
| 4. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply butyl tape to the front door panel.
![]() |
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
Attach the front door service hole cover according to the reference points on the front door panel.
| *1 | Reference Point |
| 5. INSTALL FRONT DOOR TRIM BRACKET |
![]() |
Install the front door trim bracket with the 2 screws.
| 6. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
![]() |
Engage the 2 claws and install the front door inside handle sub-assembly to the front door trim board sub-assembly.
| 7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Engage the 9 clips and install the front door trim board sub-assembly.
Install the 2 screws.
Remove the 2 pieces of protective tape.
| 8. INSTALL COURTESY LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the claw to install the courtesy light assembly.
| 9. INSTALL DOOR ARMREST COVER |
![]() |
Install the door armrest cover.
| 10. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
![]() |
Connect the connector.
Engage the 7 claws and 3 guides, and install the power window regulator master switch assembly with front door armrest base panel.
| 11. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
Connect the connector.
![]() |
Engage the 7 claws and 3 guides, and install the power window regulator switch assembly with front door armrest base panel.
| 12. INSTALL ASSIST GRIP COVER |
![]() |
Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.
| 13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws and install the front door inside handle bezel plug.
| 14. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 15. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 16. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 17. INITIALIZE POWER WINDOW CONTROL SYSTEM |