REAR DOOR BELT MOULDING > INSTALLATION |
| 1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 7 claws to install the rear door belt moulding assembly.
| 2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.
Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator switch assembly and rear power window regulator motor connector.
w/ Navigation System for HDD:
Disconnect the cable from the negative (-) battery terminal.
![]() |
Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as shown in the illustration.
Install the rear door glass sub-assembly with the 2 bolts.
Connect the cable to the negative (-) battery terminal.
| 3. INSTALL REAR DOOR REAR GUIDE SEAL |
Install the temporary screw to the rear door rear guide seal.
![]() |
Temporarily install the rear door rear guide seal.
| *1 | Temporary Screw |
Install the 2 screws.
Tighten the temporary screw to install the rear door rear guide seal.
| 4. INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY |
![]() |
Install the screw.
Install the rear door window guide sub-assembly with the bolt.
| 5. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 6. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
| *1 | Reference Point |
Connect the 2 connectors.
Engage the clamp.
| 7. INSTALL REAR DOOR TRIM BRACKET |
![]() |
Install the rear door trim bracket with the 2 screws.
| 8. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
![]() |
Engage the 2 claws and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
| 9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
for 8 Speakers:
Connect the connector.
![]() |
Engage the 8 clips and install the rear door trim board sub-assembly.
Install the 2 screws.
Remove the protective tape.
| 10. INSTALL REAR DOOR ARMREST COVER |
![]() |
Install the rear door armrest cover.
| 11. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
Connect the connector.
![]() |
Engage the 7 claws and 2 guides, and install the rear power window regulator switch assembly with rear door armrest base panel.
| 12. INSTALL DOOR ASSIST GRIP COVER |
![]() |
Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.
| 13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws and install the rear door inside handle bezel plug.
| 14. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 15. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 16. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 17. INITIALIZE POWER WINDOW CONTROL SYSTEM |