Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > REMOVAL

for Preparation Click here


HINT:
  1. The front side quarter window glass can be reused. When installing the window, if any of the clips on the quarter window glass are broken, butyl tape can be used to support the glass until the applied adhesive hardens.
  2. When using butyl tape to temporarily secure the window, make sure that the butyl tape is not applied exactly at the original clip location. If the butyl tape is applied exactly at the clip location, it will cause the window to protrude
  3. Use the same procedure for the RH side and LH side.
  4. The procedure listed below is for the LH side.



1. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. REMOVE REAR DOOR SCUFF PLATE


    B227766
  1. Disengage the 7 claws and remove the rear door scuff plate LH.



5. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


6. REMOVE REAR SEAT CUSHION ASSEMBLY


    B229992E01
  1. Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.
    Text in Illustration 
    *1
    100 mm (3.94 in.) or less
    *2
    Hook
    *3
    Guide

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the above procedure for the other hook.

  1. Disengage the 2 guides of the seat cushion from the seatback.

  1. Remove the rear seat cushion assembly.



7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for LH Side)


    B230041
  1. Remove the bolt.



    B230042
  1. Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.



8. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for RH Side)


    B230044
  1. Remove the bolt.



    B230045
  1. Disengage the 2 guides and remove the rear side seatback assembly RH as shown in the illustration.



9. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.



10. REMOVE REAR NO. 4 FLOOR BOARD


    B227789
  1. Disengage the guide and remove the rear No. 4 floor board.



11. REMOVE DECK FLOOR BOX LH (for LH Side)


    B227790
  1. Remove the clip.

  1. Disengage the 2 guides and remove the deck floor box LH.



12. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792
  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



13. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793
  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



14. REMOVE REAR NO. 1 FLOOR BOARD


    B227794
  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



15. REMOVE DECK TRIM SERVICE HOLE COVER


    B227795
  1. Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.



16. REMOVE REAR DECK TRIM COVER


    B227796
  1. Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.



17. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


    B227798
  1. Remove the 2 bolts.

  1. Disengage each guide and remove the 2 luggage hold belt striker assemblies.



18. REMOVE TONNEAU COVER HOLDER CAP


    B227799E01
  1. Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Remove the screw.

  1. Disengage the 7 claws and 2 clips.



  1. Disconnect the connector and remove the deck trim side panel assembly LH.


    B227804



20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Remove the screw.



  1. Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.


    B227803



21. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY


  1. Disengage the 9 clips and remove the roof side inner garnish assembly LH.


    B227806



22. REMOVE QUARTER WINDOW ASSEMBLY


    B230128E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
    Text in Illustration 
    *1
    Protective Tape



    B229487E01
  1. Place matchmarks on the quarter window assembly and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Do not allow the piano wire to interfere with the clips.



    B275804E01
  1. Pass a piano wire between the vehicle body and glass from the interior as shown in the illustration.

    HINT:
    Ensure not to interfere with the clips when passing the piano wire.

    Text in Illustration 
    *1
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    NOTICE:
    When separating the quarter window assembly from the vehicle, be careful not to damage the paint or interior and exterior ornaments.

  1. Cut off the adhesive by pulling the piano wire around the quarter window assembly.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



    B229489
  1. Disengage the 3 clips.

  1. Using suction cups, remove the glass.

    NOTICE:
    Be careful not to drop the glass.



23. CLEAN VEHICLE BODY


    B106081E15
  1. Clean and shape the contact surfaces of the vehicle body.
    Text in Illustration 
    *1
    Adhesive
    *2
    Vehicle Body

    1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

  1. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

    HINT:
    Even if all the adhesive has been removed, clean the vehicle body.