Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM

INTELLIGENT PARKING ASSIST SYSTEM > TERMINALS OF ECU

for Preparation Click here



PARKING ASSIST ECU

E224374E04

  1. Disconnect the L152 connector from the parking assist ECU.

  2. Measure the voltage and resistance of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L152-1 (+B) - L152-4 (GND1)
    SB - W-B
    Power source signal
    Power switch off
    11 to 14 V
    L152-4 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L152-8 (IG) - L152-4 (GND1)
    B - W-B
    IG power source signal
    Power switch on (IG)
    11 to 14 V
    L152-9 (ACC) - L152-4 (GND1)
    GR - W-B
    ACC power source signal
    Power switch on (ACC)
    11 to 14 V
    L152-11 (TX+) - L152-10 (TX-)
    LG - P
    AVC-LAN communication signal
    -
    -
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the L152 connector to the ECU.

  4. Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L151-1 (CSB3) - L152-4 (GND1)
    G - W-B
    Power source to ultrasonic sensor
    Power switch on (READY)
    7.2 to 8.8 V
    L151-2 (CSG3) - L152-4 (GND1)
    R - W-B
    Ultrasonic sensor ground
    Always
    Below 1 Ω
    L151-8 (HO1) - L152-4 (GND1)
    *1
    SB - W-B
    Rear height control sensor signal output
    Power switch off
    Below 1 V
    Power switch on (IG)
    0.5 to 5.25 V
    L151-9 (HI1) - L152-4 (GND1)
    L - W-B
    Rear height control sensor signal input
    Power switch off
    Below 1 V
    Power switch on (IG)
    0.5 to 5.25 V
    L151-14 (CB+) - L152-4 (GND1)
    W - W-B
    Power source to rear television camera
    Power switch on (READY)
    reverse (R) selected
    5.8 to 7.0 V
    L151-15 (CV+) - L152-4 (GND1)
    R - W-B
    Rear television camera display signal (NTSC) input
    Power switch on (READY)
    Reverse (R) selected
    Camera lens not covered, displaying an image
    Pulse generation
    (See waveform 1)
    Power switch on (READY)
    Reverse (R) selected
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)
    L151-19 (LIN3)
    GR
    Ultrasonic sensor signal input and output
    -
    -
    L151-26 (ISSW) - L152-4 (GND1)
    L - W-B
    Parking assist pre support signal input
    Power switch on (READY)
    Parking assist pre support switch assembly pushed in
    Below 1 V
    Power switch on (READY)
    Parking assist pre support switch assembly not pushed
    4.75 to 5.25 V
    L151-27 (HBL+) - L152-4 (GND1)
    *1
    P - W-B
    Rear height control sensor power supply
    Power switch off
    Below 1 V
    Power switch on (IG)
    4.75 to 5.25 V
    L151-28 (HB+) - L152-4 (GND1)
    *1
    P - W-B
    Rear height control sensor power supply
    Power switch off
    Below 1 V
    Power switch on (IG)
    4.75 to 5.25 V
    L151-29 (HGND) - Body ground
    *1
    Y - Body ground
    Rear height control sensor ground
    Always
    Below 1 Ω
    L151-30 (HBE+) - L152-4 (GND1)
    *2
    P - W-B
    Rear height control sensor power supply
    Power switch off
    Below 1 V
    Power switch on (IG)
    4.75 to 5.25 V
    L151-31 (HG1) - Body ground
    Y - Body ground
    Rear height control sensor ground
    Always
    Below 1 Ω
    L151-37 (CGND) - L152-4 (GND1)
    G - W-B
    Rear television camera ground (shield)
    Always
    Below 1 V
    L151-38 (CV-) - L152-4 (GND1)
    B - W-B
    Rear television camera ground
    Always
    Below 1 V
    L151-39 (CANL) - L152-4 (GND1)
    BR - W-B
    CAN communication signal
    CAN communication circuit
    Pulse generation
    L151-40 (CANH) - L152-4 (GND1)
    Y - W-B
    CAN communication signal
    CAN communication circuit
    Pulse generation
    L123-1 (GVIF)
    B
    Video signal (Digital)
    -
    -
    If the result is not as specified, the ECU may have a malfunction.
    *1: for LED headlight
    *2: for Halogen headlight



  5. E171712E22
  6. Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


    1. Waveform 1 (camera lens is not covered, displaying an image)
      Item
      Content
      Terminal No. (Symbol)
      L151-14 (CB+) - L152-4 (GND1)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Power switch on (READY), reverse (R) selected

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)
      Item
      Content
      Terminal No. (Symbol)
      L151-14 (CB+) - L152-4 (GND1)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Power switch on (READY), reverse (R) selected

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1 (camera lens not covered, displaying an image)
      *b
      Waveform 2 (camera lens covered, blacking out the screen)
      *c
      Synchronization Signal
      *d
      Video Waveform


REAR TELEVISION CAMERA ASSEMBLY

E228118E02

  1. Disconnect the V6 connector from the rear television camera assembly.

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V6-3 (CGND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    V6-4 (CB+) - V6-3 (CGND)
    W - W-B
    Power source
    Power switch on (READY)
    Reverse (R) selected
    5.8 to 7.0 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the V6 connector to the rear television camera assembly.

  4. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V6-2 (CV+) - V6-1 (CV-)
    R - B
    Display signal
    Power switch on (READY)
    Reverse (R) selected
    Camera lens not covered, displaying an image
    Pulse generation
    (See waveform 1)
    Power switch on (READY)
    Reverse (R) selected
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

    If the result is not as specified, the camera may have a malfunction.



  5. E171712E22
  6. Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


    1. Waveform 1 (camera lens is not covered, displaying an image)
      Item
      Content
      Terminal No. (Symbol)
      V6-2 (CV+) - V6-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Power switch on (READY), reverse (R) selected

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)
      Item
      Content
      Terminal No. (Symbol)
      V6-2 (CV+) - V6-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Power switch on (READY), reverse (R) selected

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1 (camera lens not covered, displaying an image)
      *b
      Waveform 2 (camera lens covered, blacking out the screen)
      *c
      Synchronization Signal
      *d
      Video Waveform


NAVIGATION ECU SUB-ASSEMBLY (Click here)

HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight) (Click here)