Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE

NAME PLATE > INSTALLATION

for Preparation Click here


HINT:
When installing new name plates or emblems, heat the vehicle body and name plates using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Name Plate or emblem
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body, name plates or emblems excessively.



1. INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM


    B229369E01
  1. Install the luggage compartment door emblem with the pin and 3 claws.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the vehicle body.



2. INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install a new No. 1 luggage compartment door name plate.

    1. Using a heat light, heat the vehicle body and the No. 1 luggage compartment door name plate.

    2. Remove the release paper from the No. 1 luggage compartment door name plate.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. Install the No. 1 luggage compartment door name plate as shown in the illustration.


      B229372E01


      Text in Illustration 
      *1
      Location Pin
      -
      -



3. INSTALL NO. 2 BACK DOOR NAME PLATE
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install a new No. 2 back door name plate.

    1. Using a heat light, heat the vehicle body and the No. 2 back door name plate.

    2. Remove the release paper from the No. 2 back door name plate.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. Install the No. 2 back door name plate as shown in the illustration.


      B229376E01


      Text in Illustration 
      *1
      Location Pin
      -
      -



4. INSTALL BACK DOOR NAME PLATE
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install a new back door name plate.

    1. Using a heat light, heat the vehicle body and the back door name plate.

    2. Remove the release paper from the back door name plate.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. Install the back door name plate as shown in the illustration.


      B229379E01


      Text in Illustration 
      *1
      Location Pin
      -
      -



5. INSTALL SIDE PANEL EMBLEM
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install a new side panel emblem.

    1. Using a heat light, heat the vehicle body and the side panel emblem.

    2. Remove the release paper from the side panel emblem.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. Install the side panel emblem as shown in the illustration.


      B229365E01


      Text in Illustration 
      *1
      Location Pin
      -
      -

      HINT:
      Use the same procedure for the RH side and LH side.