Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here



CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body or Illuminated Entry / Utility / Customize.

  5. Select the setting by referring to the table below.

    Wireless Door Lock Control System 
    Display (item)
    Default
    Function
    Setting
    Wireless Control
    ON
    Function that turns wireless door lock function on or off
    ON or OFF
    Hazard Answer Back
    ON
    When the doors are locked by wireless operation, the hazard warning lights flash once.
    When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
    ON or OFF
    Open Door Warning
    ON
    The buzzer sounds when lock is pressed when any of the doors are ajar.
    ON or OFF
    Panic Function*1
    ON
    Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds
    ON or OFF
    Auto Lock Time
    30 s
    Function that regulates the interval between unlocking and automatic relocking of doors
    30 s, 60 s or 120 s
    Wireless Buzzer Resp*2
    ON
    Wireless door lock buzzer response
    ON or OFF
    Wireless Buzzer Vol
    Level7
    Wireless door lock buzzer volume
    Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0

    1. *1: w/ Panic Function
    2. *2: for Australia

    Illuminated Entry 
    Display
    Default
    Content
    Setting
    Lighting Time
    15 s
    Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).)
    7.5 s, 15 s or 30 s


CUSTOMIZING FUNCTION WITH MULTI-DISPLAY

HINT:
The items in the table below can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current setting before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the multi-display (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Auto Relock Timer
      30 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Lights
      On
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Tone
      7
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

    4. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).)
      Off, 7.5 sec., 15 sec. or 30 sec.
      Main body ECU (Multiplex network body ECU)

  2. Customizing with the multi-display (for Radio and Display Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Lock Feedback Volume
      7
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)