Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the manual up and down function can be performed but the auto up and down function cannot, the fail-safe mode may be functioning.
If the power window initialization (Click here) has not been performed, the auto up and down function will not operate.

WIRING DIAGRAM


B203367E43


INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses a multiplex communication system (LIN communication system). Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  2. When the power window regulator motor assembly (for front passenger side) is reinstalled or replaced, the power window control system must be initialized.
  3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
    1. Close the power window by fully pulling up the power window regulator switch assembly (for front passenger side) and holding it at the auto up position.
    2. Open the power window by fully pushing down the power window regulator switch assembly (for front passenger side).
  4. When the ECU determines that the power window regulator motor assembly (for front passenger side) has a malfunction, DTC B2311 is set.

1.READ VALUE USING INTELLIGENT TESTER (P-Door Motor)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / P-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Side)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto switch signal / ON or OFF
    ON: Front passenger door power window auto switch operated
    OFF: Front passenger door power window auto switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


2.PERFORM INITIALIZATION (for Front Passenger Side)
  1. Initialize the power window regulator motor assembly (for front passenger side) (Click here).


NEXT


3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
  1. Check that the front passenger side door power window moves when the auto up and down function of the power window regulator switch assembly (for front passenger side) is operated (Click here).

    OK:
    Front passenger side auto up and down function is normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) (Click here)
OK

END (PROBLEM DUE TO INITIALIZATION FAILURE) 

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)


    B203473E04
  1. Remove the power window regulator switch assembly (for front passenger side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Power Window Regulator Switch Assembly (for Front Passenger Side))



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW SWITCH - REGULATOR MOTOR)


    B203481E29
  1. Disconnect the power window regulator motor assembly (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    N7-8 (AUTO) - N2-4 (AUTO)
    Always
    Below 1 Ω
    N7-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    O7-8 (AUTO) - O2-4 (AUTO)
    Always
    Below 1 Ω
    O7-8 (AUTO) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Power Window Regulator Switch Assembly (for Front Passenger Side))
    *2
    Front view of wire harness connector
    (to Power Window Regulator Motor Assembly (for Front Passenger Side))
    *3
    for LHD
    *4
    for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) (Click here)