FRONT BUMPER > REASSEMBLY |
| 1. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH |
![]() |
Engage the guide and install the front side member bracket sub-assembly LH.
Install the 4 bolts.
| 2. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH |
| 3. INSTALL FRONT BUMPER SIDE SUPPORT LH |
![]() |
Engage the 2 claws and install the front bumper side support LH.
| *1 | Bolt |
| *2 | Screw |
Install the bolt and screw.
| 4. INSTALL FRONT BUMPER SIDE SUPPORT RH |
| 5. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY |
![]() |
Install the front bumper reinforcement sub-assembly with the 6 bolts.
Engage the 5 clamps.
| 6. INSTALL FRONT BUMPER ENERGY ABSORBER |
![]() |
Engage the 4 guides to install the front bumper energy absorber.
| 7. INSTALL FRONT BUMPER SEAL |
Clean the vehicle front bumper reinforcement sub-assembly surface.
Remove the double-sided tape from the vehicle front bumper reinforcement sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from the front bumper seal.
![]() |
Install a new front bumper seal.
| *1 | Double-sided Tape |
| 8. INSTALL NO. 1 LOWER RADIATOR GRILLE |
![]() |
Engage the 16 claws to install the No. 1 lower radiator grille.
| 9. INSTALL FRONT BUMPER HOLE COVER LH |
![]() |
Engage the hook.
| *1 | Hook |
Engage the 2 claws and install the front bumper hole cover LH.
| 10. INSTALL FRONT BUMPER HOLE COVER RH |
| 11. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH |
![]() |
Engage the 3 claws.
for Nut Type:
Install the front turn signal light assembly with the nut.
for Screw Type:
Install the front turn signal light assembly with the screw.
Connect the connector.
| 12. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH |
| 13. INSTALL FOG LIGHT COVER LH |
![]() |
Engage the 4 claws and install the fog light cover LH.
| 14. INSTALL FOG LIGHT COVER RH |
| 15. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light) |
![]() |
Engage the 2 guides.
Install the fog light assembly with the screw.
Connect the connector.
| 16. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light) |
| 17. INSTALL FRONT FENDER LINER RETAINER |
![]() |
Engage the claw and install the front fender liner retainer.
| 18. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY |
![]() |
Engage the 2 pins and 4 claws, and install the radiator grille emblem assembly.
Install the 2 screws.
| 19. INSTALL RADIATOR GRILLE |
![]() |
Engage the 12 claws and install the radiator grille.
![]() |
Install the 4 clips.
| 20. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intelligent Parking Assist System) |
![]() |
Temporarily install the No. 1 ultrasonic sensor retainer to the front bumper.
| *1 | Protrusion |
| *2 | Keyhole |
![]() |
Engage the 2 claws to install the No. 1 ultra sonic sensor retainer to the front bumper.
| 21. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intelligent Parking Assist System) |
![]() |
Engage the 2 claws to install the No. 1 ultrasonic sensor as shown in the illustration.
![]() |
Engage the 4 claws to connect the wire harness with bracket.
Connect the connector.
| 22. INSTALL ENGINE ROOM NO. 3 WIRE |
![]() |
Engage the 7 clamps.
![]() |
Engage the 3 clamps.
![]() |
Engage the 2 clamps and install the engine room No. 3 wire.
| 23. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System) |
![]() |
Engage the 5 clamps and install the headlight cleaner hose.
| 24. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System) |
![]() |
Engage the 2 claws to install the headlight washer actuator sub-assembly.
Install the bolt.
Connect the headlight washer hose.
| 25. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System) |
| 26. INSTALL HEADLIGHT CLEANER WASHER NOZZLE LH (w/ Headlight Cleaner System) |
![]() |
Engage the 2 claws to install the headlight cleaner washer nozzle.
| 27. INSTALL HEADLIGHT CLEANER WASHER NOZZLE RH (w/ Headlight Cleaner System) |
| 28. INSTALL HOOD TO FRONT END PANEL SEAL |
![]() |
Engage the 2 clips and install the new hood to front end panel seal.
| *1 | Double-sided Tape |
Install the 7 clips.
| 29. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET |
![]() |
Install the front bumper extension mounting bracket with the 2 screws.