Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH


    B228467
  1. Engage the guide and install the front side member bracket sub-assembly LH.

  1. Install the 4 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



2. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



3. INSTALL FRONT BUMPER SIDE SUPPORT LH


    B228466E01
  1. Engage the 2 claws and install the front bumper side support LH.
    Text in Illustration 
    *1
    Bolt
    *2
    Screw

  1. Install the bolt and screw.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



4. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure for the RH side and LH side.



5. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B228464
  1. Install the front bumper reinforcement sub-assembly with the 6 bolts.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Engage the 5 clamps.



6. INSTALL FRONT BUMPER ENERGY ABSORBER


    B228462
  1. Engage the 4 guides to install the front bumper energy absorber.



7. INSTALL FRONT BUMPER SEAL
  1. Clean the vehicle front bumper reinforcement sub-assembly surface.

    1. Remove the double-sided tape from the vehicle front bumper reinforcement sub-assembly.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Remove the release paper from the front bumper seal.

    HINT:
    After removing the release paper, keep the exposed adhesive free from foreign matter.



    B234252E01
  1. Install a new front bumper seal.
    Text in Illustration 
    *1
    Double-sided Tape

    HINT:
    Use the same procedure for the RH side and LH side.



8. INSTALL NO. 1 LOWER RADIATOR GRILLE


    B228459
  1. Engage the 16 claws to install the No. 1 lower radiator grille.



9. INSTALL FRONT BUMPER HOLE COVER LH


    B228458E01
  1. Engage the hook.
    Text in Illustration 
    *1
    Hook

  1. Engage the 2 claws and install the front bumper hole cover LH.



10. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure for the RH side and LH side.



11. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH


    E236340E01
  1. Engage the 3 claws.

  1. for Nut Type:

    1. Install the front turn signal light assembly with the nut.

      Torque:
      5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

      HINT:
      Screw type front turn signal light assemblies are provided as replacement parts. When replacing the front turn signal light assembly with a new one, install it with the screw provided.

  1. for Screw Type:

    1. Install the front turn signal light assembly with the screw.

      Torque:
      1.7 N*m{ 17 kgf*cm , 15 in.*lbf }

  1. Connect the connector.



12. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



13. INSTALL FOG LIGHT COVER LH


    B228450
  1. Engage the 4 claws and install the fog light cover LH.



14. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure for the RH side and LH side.



15. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    E189619
  1. Engage the 2 guides.

  1. Install the fog light assembly with the screw.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the connector.



16. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure for the RH side and LH side.



17. INSTALL FRONT FENDER LINER RETAINER


    B228446
  1. Engage the claw and install the front fender liner retainer.

    HINT:
    Use the same procedure for the RH side and LH side.



18. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY


    B228461
  1. Engage the 2 pins and 4 claws, and install the radiator grille emblem assembly.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



19. INSTALL RADIATOR GRILLE


    B228457
  1. Engage the 12 claws and install the radiator grille.



    B228456
  1. Install the 4 clips.



20. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intelligent Parking Assist System)


    E189844E01
  1. Temporarily install the No. 1 ultrasonic sensor retainer to the front bumper.
    Text in Illustration 
    *1
    Protrusion
    *2
    Keyhole

    NOTICE:
    1. Do not damage the front bumper with the protrusion when installing the retainer.
    2. Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper.

    HINT:
    When installing the retainer, align the keyhole and protrusion as shown in the illustration.



    E189840
  1. Engage the 2 claws to install the No. 1 ultra sonic sensor retainer to the front bumper.

    HINT:
    Use the same procedure for the RH side and the LH side.



21. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intelligent Parking Assist System)


    E189842
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor as shown in the illustration.

    NOTICE:
    Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.



    E189837
  1. Engage the 4 claws to connect the wire harness with bracket.

  1. Connect the connector.

    HINT:
    Use the same procedure for the RH side and the LH side.



22. INSTALL ENGINE ROOM NO. 3 WIRE


    B228455
  1. Engage the 7 clamps.



    B228449
  1. Engage the 3 clamps.



    B228454
  1. Engage the 2 clamps and install the engine room No. 3 wire.



23. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)


    B228448
  1. Engage the 5 clamps and install the headlight cleaner hose.



24. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E214656
  1. Engage the 2 claws to install the headlight washer actuator sub-assembly.

  1. Install the bolt.

    Torque:
    1.1 N*m{ 11 kgf*cm , 10 in.*lbf }

  1. Connect the headlight washer hose.

    HINT:
    Use the same procedure for the RH side and LH side.



25. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure for the RH side and LH side.



26. INSTALL HEADLIGHT CLEANER WASHER NOZZLE LH (w/ Headlight Cleaner System)


    E189316
  1. Engage the 2 claws to install the headlight cleaner washer nozzle.

    HINT:
    Use the same procedure for the RH side and LH side.



27. INSTALL HEADLIGHT CLEANER WASHER NOZZLE RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure for the RH side and LH side.



28. INSTALL HOOD TO FRONT END PANEL SEAL


    B228447E01
  1. Engage the 2 clips and install the new hood to front end panel seal.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Install the 7 clips.



29. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


    B228445
  1. Install the front bumper extension mounting bracket with the 2 screws.