Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH


    B228467
  1. Engage the guide and install the front side member bracket sub-assembly LH.

  1. Install the 4 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



2. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



3. INSTALL FRONT BUMPER SIDE SUPPORT LH


    B294753E01
  1. Engage the 2 claws and install the front bumper side support LH.
    Text in Illustration 
    *1
    Bolt
    *2
    Screw

  1. Install the bolt and screw.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



4. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure for the RH side and LH side.



5. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B294752
  1. Engage the claw.

  1. Install the front bumper reinforcement sub-assembly with the 6 bolts.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Engage the 5 clamps.



6. INSTALL FRONT BUMPER ENERGY ABSORBER


    B294751
  1. Engage the 4 guides to install the front bumper energy absorber.



7. INSTALL FRONT BUMPER SEAL
  1. Clean the front bumper reinforcement sub-assembly surface.

    1. Remove the double-sided tape from the front bumper reinforcement sub-assembly.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Remove the release paper from the front bumper seal.

    HINT:
    After removing the release paper, keep the exposed adhesive free from foreign matter.



    B294750E01
  1. Install a new front bumper seal.
    Text in Illustration 
    *1
    Double-sided Tape

    HINT:
    Use the same procedure for the RH side and LH side.



8. INSTALL NO. 1 LOWER RADIATOR GRILLE


    B294749
  1. Engage the 20 claws to install the No. 1 lower radiator grille.

  1. Install the 2 outside moulding retainers.



9. INSTALL NO. 2 LOWER RADIATOR GRILLE


    B294748
  1. Engage the pin and 5 claws, and install the No. 2 lower radiator grille.



    B294747
  1. Install the 2 screws.



10. INSTALL FRONT BUMPER HOLE COVER LH


    B294746E01
  1. Engage the hook.
    Text in Illustration 
    *1
    Hook

  1. Engage the 3 claws and install the front bumper hole cover LH.



11. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure for the RH side and LH side.



12. INSTALL FRONT FENDER LINER RETAINER


    B294745
  1. Engage the claw and install the front fender liner retainer.

    HINT:
    Use the same procedure for the RH side and LH side.



13. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY


    B294744
  1. Engage the 2 pins and 4 claws, and install the radiator grille emblem assembly.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



14. INSTALL RADIATOR GRILLE


    B294743
  1. Engage the 12 claws and install the radiator grille.



    B294742
  1. Install the 4 clips.



15. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)


    B299342
  1. Engage the 8 clamps and install the headlight cleaner hose.



16. INSTALL ENGINE ROOM NO. 3 WIRE


    B294741
  1. Engage the 9 clamps to install the engine room No. 3 wire.



17. INSTALL HOOD TO FRONT END PANEL SEAL


    B294740E01
  1. Engage the 2 clips and install a new hood to front end panel seal.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Install the clip.



18. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


    B294739
  1. Engage the 2 claws.

  1. Install the front bumper extension mounting bracket with the 2 screws.



19. INSTALL FOG LIGHT ASSEMBLY LH
  1. Engage the 2 guides to temporarily install the fog light assembly.

  1. Install the fog light assembly with the screw.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }

  1. Connect the connector.



20. INSTALL FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



21. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH (w/o Daytime Running Light)


    E238378
  1. Engage the 2 claws to temporarily install the front turn signal light assembly.

  1. Install the front turn signal light assembly with the clip.

  1. Engage each clamp.

  1. Connect the connector.



22. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH (w/o Daytime Running Light)

HINT:
Use the same procedure for the RH side and LH side.



23. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH (w/ Daytime Running Light)


    E238382
  1. Engage the 2 claws to temporarily install the front turn signal light assembly.

  1. Install the front turn signal light assembly with the clip.

  1. Engage each clamp.

  1. Connect the connector.



24. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH (w/ Daytime Running Light)

HINT:
Use the same procedure for the RH side and LH side.



25. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intelligent Parking Assist System)


    E189844E01
  1. Temporarily install the No. 1 ultrasonic sensor retainer to the front bumper.
    Text in Illustration 
    *1
    Protrusion
    *2
    Keyhole

    NOTICE:
    1. Do not damage the front bumper with the protrusion when installing the retainer.
    2. Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper.

    HINT:
    When installing the retainer, align the keyhole and protrusion as shown in the illustration.



    E189840
  1. Engage the 2 claws to install the No. 1 ultra sonic sensor retainer to the front bumper.

    HINT:
    Use the same procedure for the RH side and the LH side.



26. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intelligent Parking Assist System)


    E189842
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor as shown in the illustration.

    NOTICE:
    Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.



    E189837
  1. Engage the 4 claws to connect the wire harness with bracket.

  1. Connect the connector.

    HINT:
    Use the same procedure for the RH side and the LH side.



27. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E239914E01
  1. Push the tab and engage the 2 claws to install the headlight washer actuator sub-assembly LH.
    Text in Illustration 
    *1
    Tab



    E239912E01
  1. Push up the No. 1 headlight cleaner clamp.
    Text in Illustration 
    *1
    No. 1 Headlight Cleaner Clamp



    E239910E01
  1. Install the No. 3 headlight cleaner clamp.
    Text in Illustration 
    *1
    No. 3 Headlight Cleaner Clamp
    *2
    Headlight Cleaner Hose

  1. Connect the headlight cleaner hose.



28. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure for the RH side and LH side.



29. INSTALL HEADLIGHT CLEANER WASHER NOZZLE COVER (w/ Headlight Cleaner System)


    E239908
  1. Engage the 2 claws to install the headlight cleaner washer nozzle cover.

    HINT:
    Use the same procedure for the RH side and LH side.