Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SECURITY HORN ASSEMBLY (for Built-in Battery type)

SECURITY HORN ASSEMBLY (for Built-in Battery type) > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side .



4. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH


5. REMOVE REAR SEAT CUSHION ASSEMBLY


    B229992E01
  1. Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.
    Text in Illustration 
    *1
    100 mm (3.94 in.) or less
    *2
    Hook
    *3
    Guide

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the above procedure for the other hook.

  1. Disengage the 2 guides of the seat cushion from the seatback.

  1. Remove the rear seat cushion assembly.



6. REMOVE REAR SIDE SEATBACK ASSEMBLY RH


    B230044
  1. Remove the bolt.



    B230045
  1. Disengage the 2 guides and remove the rear side seatback assembly RH as shown in the illustration.



7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.



8. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



9. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792
  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



10. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793
  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



11. REMOVE REAR NO. 1 FLOOR BOARD


    B227794
  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



12. REMOVE DECK TRIM SERVICE HOLE COVER


    B227795
  1. Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.



13. REMOVE REAR DECK TRIM COVER


    B227796
  1. Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.



14. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

HINT:
Use the same procedure for the RH side and LH side .



15. REMOVE TONNEAU COVER HOLDER CAP

HINT:
Use the same procedure for the RH side and LH side .



16. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Remove the screw.



  1. Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.


    B227803



17. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side .



18. REMOVE THEFT WARNING SIREN ASSEMBLY


    B300431
  1. Remove the 2 nuts.

  1. Disconnect the connector and remove the theft warning siren assembly.