Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER RUBBER

REAR WIPER RUBBER > REPLACEMENT

for Preparation Click here



1. REMOVE REAR WIPER BLADE (w/ Resin Wiper Arm)


    E189275
  1. Raise the wiper blade to the position where the claw detaches with a click sound as shown in the illustration.

    NOTICE:
    Be careful not to damage the claw.

  1. Pull the wiper blade straight toward to remove it from the wiper arm.

    NOTICE:
    Do not lower the wiper arm with the wiper blade removed. The arm tip may damage the back door glass surface.



2. REMOVE REAR WIPER BLADE (w/ Steel Wiper Arm)


    B113197
  1. Disengage the claw as shown in the illustration.



    B113198
  1. Remove the wiper blade as shown in the illustration.

    NOTICE:
    Do not lower the wiper arm with the wiper blade removed. The arm tip may damage the back door glass surface.



3. REMOVE REAR WIPER RUBBER (w/ Resin Wiper Arm)


    E186947E01
  1. Lift and pull the end of the wiper rubber protrusion from the blade stopper as shown in the illustration.

    NOTICE:
    Do not forcibly pull out the wiper rubber. The backing plates will be deformed or the blade claws will be damaged.

    HINT:
    Lightly pushing the rubber in the middle will allow it to be removed more easily.

  1. Remove the rear wiper rubber backing plates.



4. REMOVE REAR WIPER RUBBER (w/ Steel Wiper Arm)


    E057398
  1. Detach the head part (large side) of the wiper rubber from the wiper blade.



    E190128E01
  1. Remove the wiper rubber in the direction indicated by the arrow in the illustration.

    NOTICE:
    Do not pull out the wiper rubber forcibly. Doing so will deform the backing plate or damage the blade claw.

  1. Remove the 2 wiper rubber backing plates from the wiper rubber.



5. INSTALL REAR WIPER RUBBER (w/ Resin Wiper Arm)


    E158041E02
  1. Install the rear wiper rubber backing plates as shown in the illustration.

    NOTICE:
    Install the backing plates facing the correct direction.

  1. Insert the wiper rubber from the front end of the wiper blade to the rear end through the second claw.



    E163699E01
  1. After pushing the wiper rubber through the rear end claw, allow it to stick out from the rear end stopper.



    E163700E01
  1. Slide the wiper rubber through the front end claw.



6. INSTALL REAR WIPER RUBBER (w/ Steel Wiper Arm)


    I030020E04
  1. Install the 2 backing plates to the rubber.

    NOTICE:
    Install the backing plates facing the correct direction.



    B131950
  1. Install the wiper rubber to the claw of the wiper blade in the direction indicated by the arrow in the illustration.

    HINT:
    Install the wiper rubber so that the head part (large side) of the wiper rubber faces the arm axle side.



    E190127E01
  1. Attach the head part (large side) of the wiper rubber to the rear end side claw of the wiper blade.

    NOTICE:
    Push the wiper blade into the grooves of the wiper rubber to attach them completely.



7. INSTALL REAR WIPER BLADE (w/ Resin Wiper Arm)


    E189274
  1. Push the wiper blade straight toward to install it to the wiper arm.

  1. Engage the claw to install the rear wiper blade as shown in the illustration.

    NOTICE:
    Be careful not to damage the claw.



8. INSTALL REAR WIPER BLADE (w/ Steel Wiper Arm)


    B113199
  1. Engage the claw to install the wiper blade.