HYBRID CONTROL SYSTEM > Pattern Select Switch Eco Mode Circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / CAN Bus Check.
| Result | Proceed to |
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. | B |
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (ALL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Check for DTCs of all system by following the prompts on the tester screen.
| Result | Proceed to |
| No DTCs are output | A |
| DTCs are output | B |
|
| ||||
| A | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COMBINATION METER) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. ECO Mode.
Perform the "Indicat. ECO Mode" Active Test.
| Tester Display | Description | Inspection Condition | Specified Condition |
| Indicat. ECO Mode | ECO mode indicator light | ECO mode | Comes on |
| Result | Proceed to |
| The ECO mode indicator light comes on | A |
| The ECO mode indicator light does not come on | B |
|
| ||||
| A | |
| 4.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body Electrical / Air Conditioning / Data List / ECO Switch.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ECO Switch | ECO switch condition/ ON or OFF | ECO switch ON: ON ECO switch OFF: OFF | - |
| Result | Proceed to |
| The intelligent tester display changes according to the ECO switch operation. | A |
| The intelligent tester display does not changes according to the ECO switch operation. | B |
|
| ||||
| A | ||
| ||
| 5.CHECK PATTERN SELECT SWITCH (ECO SWITCH) |
![]() |
Remove the pattern select switch (ECO switch).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L78-2 (ECU) - L78-5 (E) | ECO Switch ON | Below 1 Ω |
| L78-2 (ECU) - L78-5 (E) | ECO Switch OFF | 10 kΩ or higher |
| *1 | Pattern Select Switch (ECO Switch) |
Install the pattern select switch.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (ECO SWITCH - BODY GROUND) |
![]() |
Disconnect connector L78 from the pattern select switch (ECO switch).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L78-5 (E) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Pattern Select Switch (ECO Switch)) |
Connect the pattern select switch connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (ECO SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Disconnect connector L78 from the pattern select switch.
Disconnect connector L17 from the air conditioning amplifier assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L78-2 (ECU) - L17-15 (ECOS) | Always | Below 1 Ω |
| L78-2 (ECU) or L17-15 (ECOS) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Pattern Select Switch (ECO Switch)) |
| *2 | Rear view of wire harness connector (to Air Conditioning Amplifier Assembly) |
Connect the air conditioning amplifier assembly connector.
Connect the pattern select switch connector.
|
| ||||
| OK | ||
| ||