Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > Pattern Select Switch Eco Mode Circuit

for Preparation Click here


DESCRIPTION

When selecting ECO mode, the switch operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system.

WIRING DIAGRAM


C190514E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / CAN Bus Check.

    Result:
    Result
    Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.
    A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DTC OUTPUT (ALL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Check for DTCs of all system by following the prompts on the tester screen.
    Result 
    Result
    Proceed to
    No DTCs are output
    A
    DTCs are output
    B



B
GO TO DTC CHART
A


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COMBINATION METER)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. ECO Mode.

  1. Perform the "Indicat. ECO Mode" Active Test.

    OK 
    Tester Display
    Description
    Inspection Condition
    Specified Condition
    Indicat. ECO Mode
    ECO mode indicator light
    ECO mode
    Comes on

    Result:
    Result
    Proceed to
    The ECO mode indicator light comes on
    A
    The ECO mode indicator light does not come on
    B



B
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


4.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body Electrical / Air Conditioning / Data List / ECO Switch.

  1. Read the value displayed on the intelligent tester.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ECO Switch
    ECO switch condition/
    ON or OFF
    ECO switch ON:
    ON
    ECO switch OFF:
    OFF
    -

    Result:
    Result
    Proceed to
    The intelligent tester display changes according to the ECO switch operation.
    A
    The intelligent tester display does not changes according to the ECO switch operation.
    B



B
Go to step 5
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK PATTERN SELECT SWITCH (ECO SWITCH)


    C210637E03
  1. Remove the pattern select switch (ECO switch).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-2 (ECU) - L78-5 (E)
    ECO Switch ON
    Below 1 Ω
    L78-2 (ECU) - L78-5 (E)
    ECO Switch OFF
    10 kΩ or higher

Text in Illustration 
*1
Pattern Select Switch (ECO Switch)
  1. Install the pattern select switch.



NG
REPLACE PATTERN SELECT SWITCH (ECO SWITCH)
OK


6.CHECK HARNESS AND CONNECTOR (ECO SWITCH - BODY GROUND)


    C210638E01
  1. Disconnect connector L78 from the pattern select switch (ECO switch).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-5 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Front view of wire harness connector
(to Pattern Select Switch (ECO Switch))
  1. Connect the pattern select switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ECO SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect connector L78 from the pattern select switch.

  1. Disconnect connector L17 from the air conditioning amplifier assembly.



    C210640E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-2 (ECU) - L17-15 (ECOS)
    Always
    Below 1 Ω
    L78-2 (ECU) or L17-15 (ECOS) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Pattern Select Switch (ECO Switch))
*2
Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
  1. Connect the air conditioning amplifier assembly connector.

  1. Connect the pattern select switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)