Home › Vehicle Interior › HEATING / AIR CONDITIONING › ROOM TEMPERATURE SENSOR

ROOM TEMPERATURE SENSOR > REMOVAL

for Preparation Click here



1. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    B223452E01
  1. Using a moulding remover, slightly lift the panel at the position shown in the illustration.
    Text in Illustration 
    *a
    Lift slightly

  1. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

  1. Disconnect each connector and remove the integration control and panel assembly.



2. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B223454
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.



    B223455
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.



3. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Disengage the 14 claws.



  1. Disconnect the connector and remove the instrument cluster finish panel garnish.


    B223458



4. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B223459
  1. Disengage the 3 claws.

  1. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.



5. REMOVE REAR CONSOLE BOX CUP HOLDER


    B279580
  1. Disengage the 4 claws and remove the rear console box cup holder as shown in the illustration.



6. REMOVE CONSOLE BOX CARPET


    B279581
  1. Remove the console box carpet.



7. REMOVE REAR CONSOLE BOX ASSEMBLY


    B279582
  1. Remove the 5 bolts.



    B279583
  1. Pull the rear console box assembly in the direction indicated by the arrow to disengage the 8 claws.

  1. Disconnect each connector and remove the rear console box assembly.



8. REMOVE ELECTRICAL KEY OSCILLATOR


    B229283
  1. Disconnect the connector.

  1. Disengage the clamp and remove the electrical key oscillator.

    NOTICE:
    Be careful when removing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.



9. REMOVE NO. 2 CONSOLE BOX MOUNTING BRACKET


    B223617
  1. Remove the 6 bolts <B> and No. 2 console box mounting bracket.



10. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    B223643E01
  1. Pull the front No. 1 console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the front No. 1 console box insert.



11. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    B223645E01
  1. Pull the front No. 2 console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the front No. 2 console box insert.



12. REMOVE BOX BOTTOM MAT


    B279571
  1. Disengage the fastener and remove the box bottom mat.



13. SEPARATE CONSOLE BOX ASSEMBLY


    B279572
  1. Remove the bolt <B> and 2 clips.



    B279573
  1. While pushing the parts shown in the illustration inward, pull the console box assembly in the direction indicated by the arrow to disengage the 2 claws and 4 guides.

  1. Disconnect the connector and separate the console box assembly.



14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E189053
  1. Disengage the 4 claws and remove the air conditioning control assembly as shown in the illustration.

  1. Disconnect the connector.

    NOTICE:
    Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, mark them so that they will not be reconnected incorrectly.



15. REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY


    C209262
  1. Disconnect the connector from the shift lock control unit assembly.

  1. Remove the 3 nuts and shift lock control unit assembly.



16. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B223654
  1. Disengage the clamp.

  1. Remove the 2 bolts <A>.



    B279574
  1. Pull the upper instrument panel finish panel assembly in the direction indicated by the arrow to disengage the 9 claws and remove the upper instrument panel finish panel assembly.



17. REMOVE NO. 1 SWITCH HOLE BASE


    B223657
  1. Disengage the 5 claws.

  1. Disconnect the connector to remove the No. 1 switch hole base.



18. REMOVE ROOM TEMPERATURE SENSOR


    E189066
  1. Disengage the 2 claws and remove the room temperature sensor from the No. 1 switch hole base.