Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY

REAR COMBINATION LIGHT ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE REAR BUMPER ASSEMBLY


    B228475E01
  1. Put protective tape around the rear bumper assembly.
    Text in Illustration 
    *1
    Protective Tape



    B228476
  1. Remove the 2 screws and 2 rear bumper upper stoppers.



    B228477
  1. Using a clip remover, remove the 9 clips.

  1. Remove the nut.



    B228478
  1. Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disengage the claw.

    HINT:
    Use the same procedure for the RH side and LH side.



    B228479
  1. Disengage the 5 claws.

    HINT:
    Use the same procedure for the RH side and LH side.



    B228481
  1. Disengage the 4 claws and remove the rear bumper assembly as shown in the illustration.



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD (for RH Side)


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. REMOVE REAR NO. 4 FLOOR BOARD (for LH Side)


    B227789
  1. Disengage the guide and remove the rear No. 4 floor board.



6. REMOVE DECK FLOOR BOX LH (for LH Side)


    B227790
  1. Remove the clip.

  1. Disengage the 2 guides and remove the deck floor box LH.



7. REMOVE REAR DOOR SCUFF PLATE


    B227766
  1. Disengage the 7 claws and remove the rear door scuff plate LH.



8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    B227770
  1. Remove the rear door opening trim weatherstrip LH.



9. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.



10. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792
  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



11. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793
  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



12. REMOVE REAR NO. 1 FLOOR BOARD


    B227794
  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



13. REMOVE DECK TRIM SERVICE HOLE COVER


    B227795
  1. Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.



14. REMOVE REAR DECK TRIM COVER


    B227796
  1. Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.



15. REMOVE REAR SEAT CUSHION ASSEMBLY


    B229992E01
  1. Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.
    Text in Illustration 
    *1
    100 mm (3.94 in.) or less
    *2
    Hook
    *3
    Guide

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the above procedure for the other hook.

  1. Disengage the 2 guides of the seat cushion from the seatback.

  1. Remove the rear seat cushion assembly.



16. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for LH Side)


    B230041
  1. Remove the bolt.



    B230042
  1. Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.



17. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for RH Side)

HINT:
Use the same procedure for the RH side and LH side.



18. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    B227798
  1. Remove the 2 bolts.

  1. Disengage each guide and remove the 2 luggage hold belt striker assemblies.



19. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and LH side.



20. REMOVE TONNEAU COVER HOLDER CAP (for LH Side)


    B227799E01
  1. Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



21. REMOVE TONNEAU COVER HOLDER CAP (for RH Side)

HINT:
Use the same procedure for the RH side and LH side.



22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Remove the screw.

  1. Disengage the 7 claws and 2 clips.



  1. Disconnect the connector and remove the deck trim side panel assembly LH.


    B227804



23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Remove the screw.



  1. Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.


    B227803



24. REMOVE REAR COMBINATION LIGHT ASSEMBLY


    E235369
  1. Disconnect the connector.

  1. Remove the 2 nuts.



    E235370
  1. Disengage the 2 clips and guide, and remove the rear combination light assembly as shown in the illustration.