DTC B14A2 Driver Side Solar Sensor Short Circuit |

| DTC No. | DTC Detection Condition | Trouble Area |
| B14A2 | Short in driver side solar sensor circuit |
|

| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Solar Sensor (D side) | Solar sensor / Min.: 0 Max.: 255 | Solar sensor value increases as brightness increases | - |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the solar sensor (automatic light control sensor) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I1-3 (CLTB) - I1-6 (CLTE) | Power switch off | Below 1 V |
| I1-3 (CLTB) - I1-6 (CLTE) | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to Solar Sensor (Automatic Light Control Sensor)) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - A/C AMPLIFIER) |
![]() |
Disconnect the solar sensor (automatic light control sensor) connector.
![]() |
Disconnect the A/C amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L17-33 (TS) - I1-1 (NSHA) | Always | Below 1 Ω |
| L17-33 (TS) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Solar Sensor (Automatic Light Control Sensor)) |
| *2 | Front view of wire harness connector (to A/C Amplifier) |
|
| ||||
| OK | |
| 4.INSPECT SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) |
![]() |
Remove the solar sensor (automatic light control sensor).
Reconnect the solar sensor (automatic light control sensor) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I1-1 (NSHA) - I1-6 (CLTE) | Sensor is exposed to electric light | 0.8 to 4.3 V |
| I1-1 (NSHA) - I1-6 (CLTE) | Sensor is covered with a cloth | Below 0.8 V |
| *1 | Component with harness connected (Solar Sensor (Automatic Light Control Sensor)) |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR) |
![]() |
Disconnect the main body ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L7-20 (CLTB) - I1-3 (CLTB) | Always | Below 1 Ω |
| L7-22 (CLTE) - I1-6 (CLTE) | Always | Below 1 Ω |
| L7-20 (CLTB) - Body ground | Always | 10 kΩ or higher |
| L7-22 (CLTE) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Main Body ECU) |
| *2 | Front view of wire harness connector (to Solar Sensor (Automatic Light Control Sensor)) |
|
| ||||
| OK | ||
| ||