Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P0403    Exhaust Gas Recirculation Control Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC P0401 .

DTC No.
DTC Detection Condition
Trouble Area
P0403
Open or short in EGR valve circuit
(1 trip detection logic)
  1. Open or short in EGR circuit
  2. EGR valve assembly
  3. ECM

HINT:
DTC P0403 is set when the power switch is on (IG).


WIRING DIAGRAM


A220107E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE EGR VALVE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling
    MAP
    (Data List)
    MAP value is 20 to 40 kPa (150 to 300 mmHg)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.

    Result:
    Result
    Proceed to
    Within standard range
    A
    Outside of standard range
    B



B
Go to step 2
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT EGR VALVE ASSEMBLY
A209149E01
  1. Disconnect the EGR valve assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
2 (+B1) - 3 (EGR2)
20 °C (68 °F)
20 to 22 Ω
2 (+B1) - 1 (EGR4)
5 (+B2) - 4 (EGR1)
5 (+B2) - 6 (EGR3)

Text in Illustration 
*1
Component without harness connected
(EGR Valve Assembly)
  1. Reconnect the EGR valve assembly connector.



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


3.INSPECT EGR VALVE ASSEMBLY (+B1 OR +B2 VOLTAGE)
A209148E04
  1. Disconnect the EGR valve assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D10-2 (+B1) - Body ground
Power switch on (IG)
11 to 14 V
D10-5 (+B2) - Body ground

Text in Illustration 
*1
Front view of wire harness connector
(to EGR Valve Assembly)
  1. Reconnect the EGR valve assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - EFI MAIN RELAY)
OK


4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)

A216511E02

  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):

Tester Connection
Condition
Specified Condition
D28-45 (EGR1) - D10-4 (EGR1)
Always
Below 1 Ω
D28-44 (EGR2) - D10-3 (EGR2)
D28-43 (EGR3) - D10-6 (EGR3)
D28-42 (EGR4) - D10-1 (EGR4)


Standard Resistance (Check for Short):

Tester Connection
Condition
Specified Condition
D28-45 (EGR1) or D10-4 (EGR1) - Body ground
Always
10 kΩ or higher
D28-44 (EGR2) or D10-3 (EGR2) - Body ground
D28-43 (EGR3) or D10-6 (EGR3) - Body ground
D28-42 (EGR4) or D10-1 (EGR4) - Body ground


Text in Illustration 
*1
Front view of wire harness connector
(to EGR Valve Assembly)
*2
Front view of wire harness connector
(to ECM)
  1. Reconnect the ECM connector.

  1. Reconnect the EGR valve assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EGR VALVE ASSEMBLY)
OK


5.CHECK DTC OUTPUT RECORDS (DTC P0403)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Put the engine in inspection mode (Click here).

  1. Start the engine warm it up.

  1. Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC P0403 is output
    B



B
REPLACE ECM (Click here)
A

END