Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

NAVIGATION SYSTEM (for Radio and Display Type) > OPERATION CHECK

for Preparation Click here



CHECK NAVIGATION SYSTEM NORMAL CONDITION
  1. If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.
    Symptom
    Answer
    A longer route than expected is chosen.
    Depending on the road conditions, the extension module may determine that a longer route is quicker.
    Even when distance priority is high, the shortest route is not shown.
    Some routes may not be advised due to safety concerns.
    When the vehicle is put into motion immediately after the hybrid system starts, the navigation system deviates from the correct position.
    If the vehicle starts before the navigation system activates, the system may not react.
    When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position.
    When the vehicle is driving on new roads not available on the hard disk drive, the system attempts to match it to another nearby road, causing the position mark to deviate.



  2. I100066
  3. The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or extension module.

    1. The current position mark may be displayed on a nearby parallel road.



    2. I100067
    3. Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.



    4. I100068
    5. When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.



    6. I100069
    7. When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.



    8. I100070
    9. When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.



    10. I100071
    11. When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.



    12. I100072
    13. When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.



    14. E106418
    15. When the power switch is turned on (ACC or IG) and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.



    16. I100074
    17. When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.



    18. I100075
    19. When the tires are changed, the current vehicle position mark may deviate from the correct position.

      HINT:
      1. A change in tire diameter may cause a speed sensor error.
      2. Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.


CHECK PANEL & STEERING SWITCH

HINT:
  1. The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E226143
  5. Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.



  6. E225786E01
  7. Panel & Steering Switch Check Mode
    Screen Description 
    Display
    Content
    *a: Switch condition
    "Pushed" is displayed when any switch is pushed
    *b: Number of switches pushed
    1. Number of switches pushed at once is displayed
    2. If more than 3 switches are pushed at once, "More than 3" is displayed
    *c: Rotary switch direction
    Direction of rotary switch is displayed

    1. Operate each switch and check that the switch conditions are correctly displayed.

      NOTICE:
      When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E226144
  5. Select "Touch Switch" from the "Function Check/Setting I" screen.



  6. E176521
  7. Touch Switch Check

    1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK COLOR BAR

HINT:
  1. The display color on the screen is checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E226146
  5. Select "Color Bar" from the "Function Check/Setting I" screen.



  6. E226305
  7. Color Bar Check Mode

    1. Select a color bar from the "Color Bar Check Mode" screen.

    2. Check the display color.

      HINT:
      1. The entire screen turns to the color or stripe selected.
      2. Touching the display will return to the "Color Bar Check Mode" screen.


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E226148
  5. Select "Vehicle Signal" from the "Function Check/Setting I" screen.



  6. E225776
  7. Vehicle Signal Check Mode
    Screen Description 
    Display
    Content
    Battery
    Auxiliary battery voltage is displayed.
    IG
    Power switch ON/OFF state is displayed.
    PKB
    Parking brake ON/OFF state is displayed.
    REV
    Reverse signal ON/OFF state is displayed.
    SPEED
    Vehicle speed is displayed in km/h.
    TAIL
    Tail signal (Light control switch) ON/OFF state is displayed.
    ADIM/TCAN
    Brightness state DIM (with) / BRIGHT (without) is displayed.

    HINT:
    1. Only items sending vehicle signals will be displayed.
    2. This screen displays vehicle signals input to the radio and display receiver assembly.
    3. This screen is updated once per second when vehicle input signals change.


    1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.


CHECK MICROPHONE LEVEL

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E226145
  5. Select "Next Page" from the "Function Check/Setting I" screen.



  6. E226151
  7. Select "EXT BOX" from the "Function Check/Setting II" screen.



  8. E227335
  9. Select "Microphone Level" from the "Extension Module Service Mode" screen.



  10. E227337E02
  11. Microphone Level Test
    Screen Description 
    Display
    Content
    *a: Microphone input level meter
    Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

    1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      HINT:
      1. The microphone is active at all times when this screen is displayed.


CHECK DIAGNOSTICS

HINT:
  1. The connection condition of the USB device and each item (antenna) can be checked using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E225777
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E226145
  5. Select "Next Page" from the "Function Check/Setting I" screen.



  6. E226151
  7. Select "EXT BOX" from the "Function Check/Setting II" screen.



  8. E227336
  9. Select "Diagnostics" from the "Extension Module Service Mode" screen.



  10. E227338
  11. Diagnostics Tests

    1. Check the connection condition of the USB device and each item (antenna) on the "Diagnostics Tests" screen.

      HINT:
      1. "YES" is displayed when the connection is good and "NO" is displayed when it is not.
      2. If "NO" is displayed for any of the item connected conditions, check each connection condition.


CHECK SOFTWARE ERROR HISTORY

HINT:
This function is used to check the cause when the radio and display receiver assembly screen is blacked out.

  1. Check software error history.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (READY).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / Utility / Software Error History.

    5. When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.
      Software Error History Screen Description 
      Error Description
      Trigger
      Detail
      Software Reset
      Navi Microcomputer
      Hexadecimal Number
      Audio Microcomputer
      CAN Microcomputer
      No Video Signal
      Front Monitor
      Rear Monitor
      MOST Cold Restart
      Always

      HINT:
      1. Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the intelligent tester occurs, a "-" is displayed for the display items.

  2. Clear software error history.

    1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).

      1. Cleared using the intelligent tester.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.


CHECK OPTICAL DISC ERROR HISTORY

HINT:
This function is used to check the cause of an optical disc error.

  1. Check optical disc error history.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (READY).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Navigation System / Utility / Optical Disc Error History.

    5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.
      Optical Disc Error History Screen Description 
      Display
      Content
      Error Type
      Displays the type of error.
      Device
      Displays the malfunctioning device.
      Date
      Displays the date and time that the malfunction occurred.
      "Error Type" Screen Description 
      Error Type
      Detection Condition
      Action
      Read Error
      When a disc read error occurs.
      Proceed to next suspected area shown in Problem Symptoms Table (Click here)
      Disc damaged/upside down/dirty
      When it is determined that any of the following is the cause of the disc read error:
      1. The disc cannot be read.
      2. The disc cannot be read because of dirt or scratches.
      3. The disc cannot be read because it is inserted upside down.
      Cannot determine disc type
      An unsuitable disc is inserted.
      DPS error
      When an error occurs while decoding MP3/WMA files.
      Some files are corrupt
      1. When MP3/WMA files cannot be played back because they are unsupported.
      2. Even though the file extensions are MP3 or WMA, files cannot be played back because the header information cannot be read.
      Some files cannot be found
      1. When a disc without music data is played back.
      2. When there are no playable MP3/WMA files.
      Copy protection violation
      When a file with copyright protection that cannot be played back is played back.
      "Device" Screen Description 
      Device
      Component
      DVD-P
      Not available
      CD-P
      Radio and display receiver assembly
      R-Seat DVD-P
      Not available

      HINT:
      1. Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the intelligent tester occurs, a "-" or blank is displayed for the display items.

  2. Clear optical disc error history.

    1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).

      1. Cleared using the intelligent tester.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.