DTC P0C73-776 Motor Electronics Coolant Pump "A" Control Performance |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0C73 | 776 | A speed or intermittent stop malfunction occurs in the inverter water pump assembly. A revolution malfunction (speed is too high/low or stop) or an intermittent stop malfunction (operation stops intermittently when the revolution speed is abnormal) occurs in the inverter water pump assembly. |
|
| DTC No. | INF Code | Data List Item |
| P0C73 | 776 |
|
| DTC No. | INF Code | Active Test |
| P0C73 | 776 | Activate the Water Pump*1 |

| 1.CHECK QUANTITY OF HV COOLANT |
Check the coolant level in the inverter reserve tank.
Check for coolant leaks.
| Result | Proceed to |
| No leaks are found and coolant level in the inverter reserve tank assembly is above the low line. | A |
| No leaks are found and coolant level in the inverter reserve tank assembly is below the low line. | B |
| Coolant leaks are evident. | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK COOLANT HOSE |
Check if the hoses of the cooling system are kinked or clogged.
|
| ||||
| OK | |
| 3.CHECK INVERTER WATER PUMP ASSEMBLY |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List.
Select Inverter W/P Revolution in the Data List.
Read the Data List.
Turn the power switch off.
|
| ||||
| OK | |
| 4.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear DTCs and freeze frame data.
| NEXT | |
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Select Inverter W/P Revolution in the Data List.
While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.
| Data List Item | Specified Condition |
| Inverter W/P Revolution | 2250 to 5625 rpm |
Turn the power switch off.
|
| ||||
| OK | |
| 6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Read the freeze frame data Ambient Temperature using the intelligent tester.
Check if the freeze frame data Ambient Temperature is below freezing.
| Result | Proceed to |
| Ambient Temperature value is above freezing temperature of the HV coolant | A |
| Ambient Temperature value is below freezing temperature of the HV coolant | B |
Turn the power switch off.
|
| ||||
| A | ||
| ||
| 7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR) |
Check the connections of the power management control ECU connectors.

| *1 | for LHD | *2 | for RHD |
|
| ||||
| OK | |
| 8.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR) |
![]() |
Check the connection of the inverter water pump assembly connector.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY) |
Disconnect connector A21 from the power management control ECU.
Disconnect connector g1 from the inverter water pump assembly.
Measure the resistance according to the value(s) in the table below.

| *1 | Rear view of wire harness connector (to Power Management Control ECU) | *2 | Front view of wire harness connector (to Inverter Water Pump Assembly) |
| Tester Connection | Switch Condition | Specified Condition |
| g1-3 (SWP) - A21-13 (IWP) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| g1-3 (SWP) or A21-13 (IWP) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the power management control ECU connector.
Connect the inverter water pump assembly connector.
|
| ||||
| OK | |
| 10.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION) |
Connect the intelligent tester to the DLC3.
Remove the IGCT No. 3 fuse from engine room junction block assembly.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / ECU Data List.
Select Inverter W/P Revolution in the Data List.
Read the Data List.
Turn the power switch off.
Install the IGCT No. 3 fuse.
|
| ||||
| OK | |
| 11.CHECK POWER MANAGEMENT CONTROL ECU |
Turn the power switch on (IG).
![]() |
While turning the power switch on (IG), check the waveform between the power management control ECU terminals.
| Item | Content |
| Terminal | A21-13 (IWP) - L5-6 (E1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Power switch on (IG) |
| *1 | Component with Harness Connected (Power Management Control ECU) |
Turn the power switch off.
|
| ||||
| OK | ||
| ||