DTC P314A-828 Inverter Coolant Pump Speed Signal |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P314A | 828 | When either of the following conditions is met:
|
|
| DTC No. | INF Code | Data List Item |
| P314A | 828 |
|
| DTC No. | INF Code | Active Test |
| P314A | 828 | Activate the Water Pump*2 |
| 1.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear DTCs and freeze frame data.
| NEXT | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Perform the Activate the Water Pump Active Test.
Touch the inverter water pump assembly and check that it is operating (vibrating).
Turn the power switch off.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR) |
Check the connections of the power management control ECU connectors.

| *1 | for LHD | *2 | for RHD |
|
| ||||
| OK | |
| 4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR) |
![]() |
Check the connection of the inverter water pump assembly connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY) |
Disconnect connector A21 from the power management control ECU.
Disconnect connector g1 from the inverter water pump assembly.
Measure the resistance according to the value(s) in the table below.

| *1 | Rear view of wire harness connector (to Power Management Control ECU) | *2 | Front view of wire harness connector (to Inverter Water Pump Assembly) |
| Tester Connection | Switch Condition | Specified Condition |
| g1-2 (NWP) - A21-14 (NIWP) | Power switch off | Below 1 Ω |
| g1-2 (NWP) or A21-14 (NIWP) -Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the power management control ECU connector.
Connect the inverter water pump assembly connector.
|
| ||||
| OK | |
| 6.CHECK POWER MANAGEMENT CONTROL ECU |
Disconnect connector g1 from the inverter water pump assembly.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A21-14 (NIWP) - L5-6 (E1) | Power switch on (IG) | 11 to 14 V |
| *1 | Component with harness connected (to Power Management Control ECU) |
Turn the power switch off.
Connect the inverter water pump assembly connector.
|
| ||||
| OK | |
| 7.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear DTCs and freeze frame data.
| NEXT | |
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Perform the "Activate the Water Pump" Active Test.
![]() |
Connect an oscilloscope between the power management control ECU terminals specified in the table below, and measure the waveform.
| Item | Content |
| Terminal | A21-14 (NIWP) - L5-6 (E1) |
| Equipment Setting | 5 V/DIV., 100 ms./DIV. |
| Condition | Power switch on (IG), during Active Test |
| *a | Component with harness connected (Power Management Control ECU) |
Turn the power switch off.
|
| ||||
| OK | ||
| ||
| 9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR) |
![]() |
Check the connection of the inverter water pump assembly connector.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)) |
Remove the IGCT relay from the engine room junction block assembly.
Disconnect connector g1 from the inverter water pump assembly.
While slightly shaking the wire harness, connector and engine room relay block and junction block assembly, measure the resistance according to the value(s) in the table below.

| *1 | Engine Room Relay Block and Junction Block Assembly | *2 | IGCT relay |
| *a | Front view of wire harness connector (to Inverter Water Pump Assembly) | - | - |
| Tester Connection | Switch Condition | Specified Condition |
| 5 (IGCT relay) - g1-4 (+BWP) | Power switch off | Below 1 Ω |
![]() |
| *a | Example |
| *b | Shake Slightly |
| *c | Vibrate Slightly |
Connect the inverter water pump assembly connector.
Install the IGCT relay.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND) |
Disconnect connector g1 from the inverter water pump assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| g1-1 (GND) - Body ground | Power switch on (IG) | Below 1 Ω |
| *1 | Front view of wire harness connector (to Water Pump with Motor Assembly) |
Connect the inverter water pump assembly connector.
|
| ||||
| OK | ||
| ||
| 12.CHECK FUSE (IGCT NO. 3) |
![]() |
Remove the IGCT No. 3 fuse from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| IGCT No. 3 fuse | Always | Below 1Ω |
| *1 | Engine Room Junction Block Assembly |
| *2 | IGCT No. 3 Fuse |
Install the IGCT No. 3 fuse.
|
| ||||
| OK | ||
| ||
| 13.CHECK INSTALLATION CONDITION (IGCT NO. 3 FUSE) |
Check installation condition of the IGCT No. 3 fuse.
|
| ||||
| OK | |
| 14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT) |
Remove the IGCT No. 3 fuse from the engine room junction block assembly.
Remove the IGCT relay from the engine room relay block and junction block assembly.
Disconnect connector g1 from the inverter water pump assembly.
Measure the resistance according to the value(s) in the table below.

| *1 | Engine Room Relay Block and Junction Block Assembly | *2 | IGCT No. 3 Fuse |
| *3 | IGCT Relay | - | - |
| *a | Front view of wire harness connector (to Inverter Water Pump Assembly) | - | - |
| Tester Connection | Switch Condition | Specified Condition |
| 2 (IGCT No. 3 fuse) - g1-4 (+BWP) | Power switch off | Below 1 Ω |
| 1 (IGCT No. 3 fuse) - 5 (IGCT relay) | Power switch off | Below 1 Ω |
| 2 (IGCT No. 3 fuse) or g1-4 (+BWP) - Body ground and other terminals | Power switch off | 10kΩ or higher |
Connect the inverter water pump assembly connector.
Install the IGCT relay.
Install the IGCT No. 3 fuse.
|
| ||||
| OK | |
| 15.CHECK FUSE (IGCT NO. 3) |
![]() |
Remove the IGCT No. 3 fuse from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| IGCT No. 3 fuse | Always | Below 1Ω |
| *1 | Engine Room Junction Block Assembly |
| *2 | IGCT No. 3 Fuse |
Install the IGCT No. 3 fuse.
|
| ||||
| OK | ||
| ||
| 16.CHECK FUSE HOLDER TERMINAL (IGCT NO. 3) |
Check the terminals of the IGCT No. 3 fuse holder.
|
| ||||
| OK | |
| 17.CHECK FUSE (IGCT NO. 3) |
![]() |
Remove the IGCT No. 3 fuse from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| IGCT No. 3 fuse | Always | Below 1Ω |
| *1 | Engine Room Junction Block Assembly |
| *2 | IGCT No. 3 Fuse |
Install the IGCT No. 3 fuse.
|
| ||||
| OK | ||
| ||
| 18.CHECK FUSE (IGCT NO. 3) |
![]() |
Remove the IGCT No. 3 fuse from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| IGCT No. 3 fuse | Always | Below 1Ω |
| *1 | Engine Room Junction Block Assembly |
| *2 | IGCT No. 3 Fuse |
Install the IGCT No. 3 fuse.
|
| ||||
| OK | ||
| ||
| 19.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)) |
Disconnect connector g1 from the inverter water pump assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| g1-1 (GND) - Body ground | Power switch on (IG) | Below 1 Ω |
| *1 | Front view of wire harness connector (to Water Pump with Motor Assembly) |
Connect the inverter water pump assembly connector.
|
| ||||
| OK | |
| 20.CHECK FUSE HOLDER TERMINAL (IGCT NO. 3 FUSE) |
Check the terminals of the IGCT No. 3 fuse holder.
|
| ||||
| OK | |
| 21.REPLACE INVERTER WATER PUMP ASSEMBLY |
Replace the inverter water pump assembly (Click here).
| NEXT | ||
| ||
| 22.CHECK FUSE (IGCT NO. 3) |
![]() |
Remove the IGCT No. 3 fuse from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| IGCT No. 3 fuse | Always | Below 1Ω |
| *1 | Engine Room Junction Block Assembly |
| *2 | IGCT No. 3 Fuse |
Install the IGCT No. 3 fuse.
|
| ||||
| OK | ||
| ||
| 23.CONNECT SECURELY |
| NEXT | ||
| ||
| 24.REPAIR OR REPLACE HARNESS OR CONNECTOR |
| NEXT | ||
| ||
| 25.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 3 FUSE HOLDER) |
| NEXT | ||
| ||