Home › Engine / Hybrid System › 2ZR-FXE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. INSTALL ENGINE ON ENGINE STAND
  1. Install the engine onto an engine stand with bolts and nuts.



2. REMOVE ENGINE HANGERS


    A214905
  1. Remove the 2 bolts and 2 engine hangers.



3. REMOVE THROTTLE BODY ASSEMBLY


  1. Type A:



      A212316
    1. Disconnect the connector and No. 1 water by-pass hose.

    2. Disconnect the No. 2 water by-pass hose.

    3. Remove the 2 bolts, 2 nuts and throttle body assembly.



    4. A212317
    5. Remove the gasket from the intake manifold.



  1. Type B:



      A288947
    1. Disconnect the connector and No. 1 water by-pass hose.

    2. Disconnect the No. 2 water by-pass hose.

    3. Remove the 4 bolts and throttle body assembly.



    4. A288948
    5. Remove the gasket from the intake manifold.



4. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.



    A213046
  1. Remove the 2 bolts, clamp and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



5. REMOVE EGR PIPE ASSEMBLY (w/ EGR System)


    A212663
  1. Disconnect the 2 wire harness clamps.



    A212664
  1. Remove the bolt and wire harness support.



    A212665
  1. Remove the 4 bolts, EGR pipe assembly and 2 gaskets.



6. REMOVE EGR VALVE ASSEMBLY (w/ EGR System)


    A212666
  1. Disconnect the connector, wire harness clamp and 4 water hoses.



    A212667E01
  1. Remove the 4 nuts and bolt.
    Text in Illustration 
    *1
    Stud Bolt and Nut

  1. Using an E8 "TORX" wrench, remove the 4 stud bolts and EGR valve with cooler assembly.

  1. Remove the gasket.



    A212668
  1. Remove the 2 nuts, EGR valve assembly and gasket.



7. REMOVE EGR COOLER SUB-ASSEMBLY (w/ EGR System)


    A212666
  1. Disconnect the connector, wire harness clamp and 4 water hoses.



    A212667E01
  1. Remove the 4 nuts and bolt.
    Text in Illustration 
    *1
    Stud Bolt and Nut

  1. Using an E8 "TORX" wrench, remove the 4 stud bolts and EGR valve with cooler assembly.

  1. Remove the gasket.



    A212669
  1. Remove the 2 nuts, EGR cooler sub-assembly and gasket.



8. REMOVE NO. 1 WATER BY-PASS PIPE (w/o EGR System)


    A264881
  1. Disconnect the 2 water hoses from the No. 1 water by-pass pipe.

  1. Remove the 2 bolts, nut and No. 1 water by-pass pipe from the cylinder head sub-assembly.

  1. Using an E8 "TORX" socket wrench, remove the stud bolt from the cylinder head sub-assembly.



9. REMOVE INTAKE MANIFOLD


  1. w/o EGR System:



      A260899
    1. Disconnect the 2 wire harness clamps from the wire harness support.



    2. A260900
    3. Remove the bolt and wire harness support from the surge tank cover.



    4. A260901
    5. Remove the 2 bolts and surge tank cover from the intake manifold.

    6. Remove the gasket from the intake manifold.



    A212682
  1. Disconnect the 3 connectors and 2 wire harness clamps.

  1. Remove the engine oil level dipstick.



    A212681
  1. Disconnect the wire harness clamp, and then remove the 2 bolts and engine oil level dipstick guide sub-assembly.

  1. Remove the O-ring from the engine oil level dipstick guide sub-assembly.



    A212683
  1. Disconnect the fuel vapor feed hose and ventilation hose from the intake manifold.



    A212684
  1. Remove the 2 bolts, 2 nuts and intake manifold.

  1. Remove the No. 1 intake manifold to head gasket from the intake manifold.



  1. w/ Stud Bolt:



      A212685
    1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts from the intake manifold.

      HINT:
      If a stud bolt is deformed or the threads are damaged, replace the stud bolt.



10. REMOVE FUEL VAPOR FEED PIPE


    A218073
  1. Remove the bolt and fuel vapor feed pipe.



11. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A216399
  1. Remove the bolt.



    A216400
  1. Remove the 2 bolts and the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies.

    NOTICE:
    Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



12. REMOVE NO. 1 DELIVERY PIPE SPACER


    A216401
  1. Remove the 2 No. 1 delivery pipe spacers from the cylinder head.



13. REMOVE FUEL INJECTOR ASSEMBLY


    A153009
  1. Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

  1. Remove the O-ring from each fuel injector assembly.

  1. For reinstallation, attach a tag or label with the corresponding cylinder number to each fuel injector shaft.

    NOTICE:
    Protect the fuel injector assemblies by covering them with plastic bags.



    A216402
  1. Remove the 4 injector vibration insulators.



14. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A288342E01
  1. Remove the 3 bolts and No. 1 exhaust manifold heat insulator.
    Text in Illustration 
    *A
    w/ EGR System
    *B
    w/o EGR System



15. REMOVE MANIFOLD STAY


    A212649
  1. Remove the 3 bolts and manifold stay.



16. REMOVE EXHAUST MANIFOLD


  1. w/ EGR System:



      A212650
    1. Remove the 7 nuts, exhaust manifold and 2 gaskets.



  1. w/o EGR System:



      A260903
    1. Remove the 5 nuts, exhaust manifold and gasket.



17. REMOVE VENTILATION HOSE


    A215741
  1. Remove the ventilation hose from the ventilation valve.



18. REMOVE IGNITION COIL ASSEMBLY


    A212292
  1. Disconnect the 4 ignition coil connectors.

  1. Remove the 4 bolts and 4 ignition coils.

    NOTICE:
    When removing each ignition coil, do not damage the plug cap on the engine head cover opening or the upper edge of the spark plug tube.