DTC P0A78-202 Drive Motor "A" Inverter Performance |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0A78 | 202 | Malfunction (short circuit) in the motor inverter inside the inverter with converter assembly |
|
| 1.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
Disconnect the generator cable and motor cable from the inverter with converter assembly.
![]() |
Check MG2 for an interphase short using a milliohmmeter.
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e1-1 (W) - e1-2 (U) | Power switch off | 152.6 to 169.0 mΩ |
| e1-2 (U) - e1-3 (V) | Power switch off | 157.6 to 174.0 mΩ |
| e1-3 (V) - e1-1 (W) | Power switch off | 151.6 to 168.0 mΩ |
| *1 | Motor Cable |
| *2 | Shield Ground |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e1-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| e1-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| e1-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
Connect the generator cable and motor cable.
Install the inverter terminal cover.
|
| ||||
| OK | |
| 2.REPLACE INVERTER WITH CONVERTER ASSEMBLY |
Replace the inverter with converter assembly (Click here).
|
| ||||
| 3.CHECK MOTOR CABLE |
Check that the service plug grip is not installed.
Remove the motor cable.
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e1-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| e1-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| e1-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Motor Cable (Inverter with Converter Assembly Side) |
| *2 | Shielded ground |
| *3 | Motor Cable (Hybrid Vehicle Transaxle Assembly Side) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e1-2 (U) - e2-3 (U) | Power switch off | Below 1 Ω |
| e1-3 (V) - e2-2 (V) | Power switch off | Below 1 Ω |
| e1-1 (W) - e2-1 (W) | Power switch off | Below 1 Ω |
| e1-2 (U) - e2-2 (V) | Power switch off | 100 MΩ or higher |
| e1-3 (V) - e2-1 (W) | Power switch off | 100 MΩ or higher |
| e1-1 (W) - e2-3 (U) | Power switch off | 100 MΩ or higher |
Install the motor cable.
|
| ||||
| OK | |
| 4.REPLACE HYBRID VEHICLE MOTOR ASSEMBLY |
Replace the hybrid vehicle motor assembly (Click here).
| NEXT | |
| 5.REPLACE INVERTER WITH CONVERTER ASSEMBLY |
Replace the inverter with converter assembly (Click here).
|
| ||||
| 6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2) |
Check that the service plug grip is not installed.
Disconnect the motor cable from the hybrid vehicle transaxle assembly.
![]() |
Check MG2 for an interphase short using a milliohmmeter.
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-3 (U) - e2-2 (V) | Power switch off | 154 to 170 mΩ |
| e2-2 (V) - e2-1 (W) | Power switch off | 148 to 164 mΩ |
| e2-1 (W) - e2-3 (U) | Power switch off | 149 to 165 mΩ |
| *1 | Hybrid Vehicle Transaxle Assembly |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-3 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| e2-2 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| e2-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
Connect the motor cable.
|
| ||||
| OK | |
| 7.REPLACE MOTOR CABLE |
Replace the motor cable (Click here).
| NEXT | |
| 8.REPLACE INVERTER WITH CONVERTER ASSEMBLY |
Replace the inverter with converter assembly (Click here).
|
| ||||
| 9.REPLACE MOTOR CABLE |
Replace the motor cable (Click here).
| NEXT | |
| 10.REPLACE HYBRID VEHICLE MOTOR ASSEMBLY |
Replace the hybrid vehicle motor assembly (Click here).
| NEXT | |
| 11.REPLACE INVERTER WITH CONVERTER ASSEMBLY |
Replace the inverter with converter assembly (Click here).
| NEXT | |
| 12.CHECK DTC OUTPUT (HV) |
Check the other DTCs that were output together with DTC P0A78-202.
| DTC No. | Relevant Diagnosis |
| P0A78-113, 284, 286, 287, 505, 506 | Drive Motor "A" Inverter Performance |
| NEXT | ||
| ||