Home › Vehicle Interior › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY

REAR CENTER SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR CENTER SEAT BELT ASSEMBLY


    B221502E01
  1. Install the rear center seat belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *1
    Protruding Part

    NOTICE:
    Do not allow the rear center seat belt assembly to overlap the protruding part of the rear seat back frame.



2. INSTALL REAR SEATBACK COVER WITH PAD RH
  1. Temporarily install the rear seatback cover with pad RH.



    B230029
  1. Engage the 4 claws and install the 2 rear seat headrest supports.



    B230028
  1. Engage the 4 claws and install the 2 rear seat center headrest supports.



    B230026E01
  1. Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to engage the 2 claws (A).

  1. Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to disengage the 2 claws (B) and remove the cover.



    B230024
  1. Engage the 2 claws and install the seat belt anchor cover cap.



    B230022
  1. Using hog ring pliers, install 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B230020
  1. Engage the 6 clips and Install the rear seatback cover with pad RH with the 3 clips.



3. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    B158420
  1. Install the bush.



    B230033
  1. Insert the pin into the rear seatback.

  1. Install the rear seat center armrest assembly with the bolt and bush.



4. INSTALL CENTER ARMREST HINGE COVER


    B230032
  1. Engage the claw and install the center armrest hinge cover as shown in the illustration.



5. INSTALL REAR SEATBACK STOP BUTTON GROMMET


    B230027
  1. Engage the 3 claws and install the rear seatback stop button grommet.



6. INSTALL REAR SEAT SHOULDER BELT GUIDE RH


    B230023
  1. Engage the guide and install the rear seat shoulder belt guide RH with the 2 screws.



7. INSTALL REAR SEATBACK COVER RH


    B230018
  1. Engage the 4 claws and install the rear seatback cover RH.



8. INSTALL REAR SEATBACK CENTER COVER (for LHD)


    B230019
  1. Engage the 4 claws and install the rear seatback center cover.



9. INSTALL REAR SEATBACK ASSEMBLY RH
  1. Place the rear seatback assembly RH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B230017
  1. Install the rear seatback assembly RH with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    B233147E01
  1. Engage the fastener.
    Text in Illustration 
    *1
    Fastener



10. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY


    B230016
  1. Install the rear seat center headrest assembly as shown in the illustration.



11. INSTALL REAR SEAT HEADREST ASSEMBLY RH


    B230013
  1. Install the rear seat headrest assembly RH as shown in the illustration.



12. CONNECT REAR CENTER SEAT BELT ASSEMBLY


    B221513E01
  1. Connect the anchor part of the rear seat inner belt assembly.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear center seat belt assembly to overlap the protruding part of the rear seat inner belt assembly RH.



13. INSTALL REAR SEAT CUSHION ASSEMBLY


    B229993E01
  1. Engage the 2 guides of the seat cushion to the seatback.
    Text in Illustration 
    *1
    100 mm (3.94 in.) or less
    *2
    Guide
    *3
    Hook

  1. Engage the 2 front hooks of the seat cushion to the vehicle body.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

    HINT:
    Confirm that the seat cushion is firmly installed.