FRONT PASSENGER SEAT BELT WARNING LIGHT > REMOVAL |
| 1. PRECAUTION (w/ Navigation System for HDD) |
| 2. REMOVE REAR NO. 2 FLOOR BOARD |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 3. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 4. REMOVE REAR NO. 3 FLOOR BOARD |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 6. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Using a moulding remover, slightly lift the panel at the position shown in the illustration.
| *a | Lift slightly |
Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.
Disconnect each connector and remove the integration control and panel assembly.
| 7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.
![]() |
Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.
| 8. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Disengage the 14 claws.
Disconnect the connector and remove the instrument cluster finish panel garnish.

| 9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
![]() |
Disengage the 3 claws.
Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.
| 10. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver) |
![]() |
Disengage the 4 claws and remove the center instrument cluster finish panel sub-assembly.
| 11. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver) |
![]() |
Remove the 4 bolts <B> and radio tuner opening cover with bracket.
| 12. REMOVE RADIO RECEIVER WITH BRACKET (w/o Navigation System) |
![]() |
Remove the 4 bolts.
![]() |
Disengage the 4 claws as shown in the illustration.
Disconnect each connector and remove the radio receiver with bracket.
| 13. REMOVE NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System) |
![]() |
Remove the 4 bolts.
![]() |
Disengage the 4 claws and remove the navigation receiver assembly with bracket as shown in the illustration.
Disconnect each connector.
| 14. REMOVE NO. 1 SIDE DEFROSTER NOZZLE |
![]() |
Using a moulding remover, slightly lift the panel at the position shown in the illustration.
| *a | Lift slightly |
Pull the No. 1 side defroster nozzle in the direction indicated by the arrow to disengage the 3 claws and remove the No. 1 side defroster nozzle.
| 15. REMOVE NO. 2 INSTRUMENT PANEL REGISTER |
![]() |
Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the claw and clip.
![]() |
Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 2 instrument panel register.
| 16. REMOVE GLOVE COMPARTMENT DOOR |
Open the glove compartment door assembly.
![]() |
Pull the glove compartment door in the direction indicated by the arrow to disengage the 7 claws.
Pull the glove compartment door in the direction indicated by the arrow to remove the glove compartment door.
| 17. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Remove the 2 screws <C>.
Disengage the 7 claws.
Disconnect the connector and remove the center instrument cluster finish panel garnish.

| 18. REMOVE PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY |
![]() |
Disengage the 2 claws and remove the passenger seat belt warning light assembly as shown in the illustration.