Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/o Rain Sensor)


  1. for Light Control Switch LH Side



      E171721E02
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      L48-1 (+S) - L48-3 (+1)
      OFF
      Below 1 Ω
      INT
      L48-2 (+B) - L48-3 (+1)
      MIST
      LO
      L48-2 (+B) - L48-4 (+2)
      HI
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-2 (EW) - L49-3 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Rear Wiper Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-6 (C1R) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-7 (+1R) - L49-2 (EW)
      L49-6 (C1R) - L49-2 (EW)
      INT
      Below 1 Ω
      L49-7 (+1R) - L49-2 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L48-5 (WR) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-7 (+1R) - L49-2 (EW)
      L48-5 (WR) - L49-2 (EW)
      WASH
      Below 1 Ω
      L48-5 (WR) - L49-2 (EW)
      ON + WASH
      Below 1 Ω
      L49-7 (+1R) - L49-2 (EW)

      If the result is not as specified, replace the windshield wiper switch assembly.
      Text in Illustration 
      *1
      Component without harness connected
      (Windshield Wiper Switch Assembly)

    2. Check the intermittent operation.

      1. Connect a voltmeter positive (+) lead to terminal L48-3 (+1) and a negative (-) lead to terminal L49-2 (EW).
      2. Connect a battery positive (+) lead to terminal L48-2 (+B) and a negative (-) lead to terminal L49-2 (EW) and L48-1 (+S).
      3. Turn the wiper switch to the INT position.
      4. Connect a battery positive (+) lead to terminal L48-1 (+S) for 5 seconds.

      5. Connect a battery negative (-) lead to terminal L48-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals L48-3 (+1) and L49-2 (EW).

        OK:
        Voltage changes as shown in the illustration.



        E056399E54

        If the result is not as specified, replace the windshield wiper switch assembly.

        Text in Illustration 
        *1
        Voltage between terminals L48-3 (+1) and L49-2 (EW)
        *2
        FAST: Connect battery negative lead to terminal L48-1 (+S)
        *3
        SLOW: Connect battery negative lead to terminal L48-1 (+S)
        -
        -



  1. for Light Control Switch RH Side



      E169424E09
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      L48-4 (+S) - L48-2 (+1)
      OFF
      Below 1 Ω
      INT
      L48-3 (+B) - L48-2 (+1)
      MIST
      LO
      L48-3 (+B) - L48-1 (+2)
      HI
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-2 (EW) - L49-1 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Rear Wiper Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-5 (C1R) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-4 (+1R) - L49-2 (EW)
      L49-5 (C1R) - L49-2 (EW)
      INT
      Below 1 Ω
      L49-4 (+1R) - L49-2 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L48-10 (WR) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-4 (+1R) - L49-2 (EW)
      L48-10 (WR) - L49-2 (EW)
      WASH
      Below 1 Ω
      L48-10 (WR) - L49-2 (EW)
      ON + WASH
      Below 1 Ω
      L49-4 (+1R) - L49-2 (EW)

      If the result is not as specified, replace the windshield wiper switch assembly.
      Text in Illustration 
      *1
      Component without harness connected
      (Windshield Wiper Switch Assembly)

    2. Check the intermittent operation.

      1. Connect a voltmeter positive (+) lead to terminal L48-2 (+1) and a negative (-) lead to terminal L49-2 (EW).
      2. Connect a battery positive (+) lead to terminal L48-3 (+B) and a negative (-) lead to terminal L49-2 (EW) and L48-4 (+S).
      3. Turn the wiper switch to the INT position.
      4. Connect a battery positive (+) lead to terminal L48-4 (+S) for 5 seconds.

      5. Connect a battery negative (-) lead to terminal L48-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals L48-2 (+1) and L49-2 (EW).

        OK:
        Voltage changes as shown in the illustration.



        E056399E54

        If the result is not as specified, replace the windshield wiper switch assembly.

        Text in Illustration 
        *1
        Voltage between terminals L48-2 (+1) and L49-2 (EW)
        *2
        FAST: Connect battery negative lead to terminal L48-4 (+S)
        *3
        SLOW: Connect battery negative lead to terminal L48-4 (+S)
        -
        -



2. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Rain Sensor)


  1. for Light Control Switch LH Side



      E171721E04
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      L48-1 (+S) - L48-3 (+1)
      OFF
      Below 1 Ω
      AUTO
      L48-2 (+B) - L48-3 (+1)
      MIST
      LO
      L48-2 (+B) - L48-4 (+2)
      HI
      L48-9 (AUTO) - L48-10 (E)
      AUTO
      Below 1 Ω
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-2 (EW) - L49-3 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Rear Wiper Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-6 (C1R) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-7 (+1R) - L49-2 (EW)
      L49-6 (C1R) - L49-2 (EW)
      INT
      Below 1 Ω
      L49-7 (+1R) - L49-2 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L48-5 (WR) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-7 (+1R) - L49-2 (EW)
      L48-5 (WR) - L49-2 (EW)
      WASH
      Below 1 Ω
      L48-5 (WR) - L49-2 (EW)
      ON + WASH
      Below 1 Ω
      L49-7 (+1R) - L49-2 (EW)

      If the result is not as specified, replace the windshield wiper switch assembly.
      Text in Illustration 
      *1
      Component without harness connected
      (Windshield Wiper Switch Assembly)



  1. for Light Control Switch RH Side



      E169424E10
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      L48-4 (+S) - L48-2 (+1)
      OFF
      Below 1 Ω
      AUTO
      L48-3 (+B) - L48-2 (+1)
      MIST
      LO
      L48-3 (+B) - L48-1 (+2)
      HI
      L48-6 (AUTO) - L48-5 (E)
      AUTO
      Below 1 Ω
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-2 (EW) - L49-1 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Rear Wiper Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L49-5 (C1R) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-4 (+1R) - L49-2 (EW)
      L49-5 (C1R) - L49-2 (EW)
      INT
      Below 1 Ω
      L49-4 (+1R) - L49-2 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      L48-10 (WR) - L49-2 (EW)
      OFF
      10 kΩ or higher
      L49-4 (+1R) - L49-2 (EW)
      L48-10 (WR) - L49-2 (EW)
      WASH
      Below 1 Ω
      L48-10 (WR) - L49-2 (EW)
      ON + WASH
      Below 1 Ω
      L49-4 (+1R) - L49-2 (EW)

      If the result is not as specified, replace the windshield wiper switch assembly.
      Text in Illustration 
      *1
      Component without harness connected
      (Windshield Wiper Switch Assembly)