Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER

NOISE FILTER > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 4 FLOOR BOARD


    B227789
  1. Disengage the guide and remove the rear No. 4 floor board.



4. REMOVE DECK FLOOR BOX LH


    B227790
  1. Remove the clip.

  1. Disengage the 2 guides and remove the deck floor box LH.



5. REMOVE REAR DOOR SCUFF PLATE LH


    B227766
  1. Disengage the 7 claws and remove the rear door scuff plate LH.



6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B227770
  1. Remove the rear door opening trim weatherstrip LH.



7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.



8. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792
  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



9. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793
  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



10. REMOVE REAR NO. 1 FLOOR BOARD


    B227794
  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



11. REMOVE DECK TRIM SERVICE HOLE COVER


    B227795
  1. Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.



12. REMOVE REAR DECK TRIM COVER


    B227796
  1. Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.



13. REMOVE REAR SEAT CUSHION ASSEMBLY


    B229992E01
  1. Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.
    Text in Illustration 
    *1
    100 mm (3.94 in.) or less
    *2
    Hook
    *3
    Guide

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the above procedure for the other hook.

  1. Disengage the 2 guides of the seat cushion from the seatback.

  1. Remove the rear seat cushion assembly.



14. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    B230041
  1. Remove the bolt.



    B230042
  1. Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.



15. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


    B227798
  1. Remove the 2 bolts.

  1. Disengage each guide and remove the 2 luggage hold belt striker assemblies.



16. REMOVE TONNEAU COVER HOLDER CAP


    B227799E01
  1. Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the screw.

  1. Disengage the 7 claws and 2 clips.



  1. Disconnect the connector and remove the deck trim side panel assembly LH.


    B227804



18. REMOVE RADIO SETTING CONDENSER

NOTICE:
When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.



    E234574
  1. Remove the nut.

  1. Disengage the clamp and disconnect the radio setting condenser with the wire harness from the vehicle body.



    E221953
  1. Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.



    E227453
  1. Using a screwdriver, bend back and break off the claw as shown in the illustration.

  1. Remove the terminal cover from the wire harness.

    NOTICE:
    1. Make sure to hold the wire harness on the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
    2. Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
    3. Check for deformation of the terminal after the wire harness has been removed from the terminal cover.