Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B15D8    Monitor Disconnected

for Preparation Click here


DESCRIPTION

The navigation ECU sub-assembly and parking assist ECU are connected via AVC-LAN communication.
When an AVC-LAN communication error occurs between the navigation ECU sub-assembly and parking assist ECU, this DTC will be stored.

DTC No.
DTC Detection Condition
Trouble Area
B15D8
Parking assist ECU is not/was not connected while the power switch is/was on (ACC or IG).
  1. Parking assist ECU power source circuit
  2. AVC-LAN circuit between navigation ECU sub-assembly and parking assist ECU
  3. Parking assist ECU
  4. Navigation ECU sub-assembly
  5. Harness or connector

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the auxiliary battery condition or hybrid system start voltage.
  2. The navigation ECU sub-assembly is the master unit.


WIRING DIAGRAM


E230081E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result:
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
      2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - AUXILIARY BATTERY, BODY GROUND)
  1. Disconnect the parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L152-4 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L152-1 (+B) - L152-4 (GND1)
    Power switch off
    11 to 14 V
    L152-8 (IG) - L152-4 (GND1)
    Power switch on (IG)
    11 to 14 V
    L152-9 (ACC) - L152-4 (GND1)
    Power switch on (ACC)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NAVIGATION ECU SUB-ASSEMBLY)
  1. Disconnect the parking assist ECU connector.

  1. Disconnect the navigation ECU sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L152-11 (TX+) - L150-3 (TX3+)
    Always
    Below 1 Ω
    L152-10 (TX-) - L150-4 (TX3-)
    Always
    Below 1 Ω
    L152-11 (TX+) - Body ground
    Always
    10 kΩ or higher
    L152-10 (TX-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE PARKING ASSIST ECU
  1. Replace the parking assist ECU (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK

END