EGR COOLER > INSTALLATION |
| 1. INSTALL EGR COOLER SUB-ASSEMBLY |
![]() |
Temporarily install a new gasket and the EGR cooler sub-assembly with the 2 nuts (A).
| *A | Nut (C), Type A |
| *B | Nut (C), Type B |
| *1 | Bolt |
| *2 | Stud Bolt and Nut |
Install 2 new gaskets and set the EGR valve with cooler assembly in place.
Using an E8 "TORX" wrench, install the 4 stud bolts.
Temporarily install the 4 nuts (B and C) and bolt.
Tighten the 2 nuts (A).
Tighten the 2 nuts (B) and bolt.
Tighten the 2 nuts (C).
![]() |
Connect the connector, wire harness clamp and 4 water hoses.
| 2. INSTALL EGR PIPE ASSEMBLY |
![]() |
Install 2 new gaskets and EGR pipe assembly with the 4 bolts.
![]() |
Install the wire harness support with the bolt.
![]() |
Connect the 2 wire harness clamps.
| 3. INSTALL AIR CLEANER CASE |
![]() |
Install the air cleaner case with the 3 bolts.
Install the hose to the 3 hose clamps.
Install the air cleaner filter element.
| 4. INSTALL INLET AIR CLEANER ASSEMBLY |
![]() |
Install the inlet air cleaner assembly with the 3 bolts.
Connect the wire harness clamp to the inlet air cleaner assembly.
Install the hose to the hose clamp.
| 5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly with the 2 clamps.
Tighten the hose clamp.
![]() |
Connect the mass air flow meter connector.
| 6. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Engage the 3 clips to install the cover.
| 7. ADD COOLANT (for Engine) |
Tighten the radiator drain cock plug.
Remove the reservoir tank cap.
![]() |
Add coolant to B line of the reservoir tank.
| *1 | B Line |
| Item | Capacity |
| Engine coolant | w/ Exhaust Heat Recirculation System: 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
| w/o Exhaust Heat Recirculation System: 6.5 liters (6.8 US qts, 5.7 lmp. qts) |
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the reservoir tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
![]() |
After the engine has cooled down, check that the coolant level is between full and low.
| *1 | Full Line |
| *2 | Low Line |
| 8. INSPECT FOR COOLANT LEAK (for Engine) |
Remove the reservoir tank cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
Remove the radiator cap tester.
Install the reservoir tank cap.
| 9. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Install the outer cowl top panel sub-assembly with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp to install the wire harness.
| 10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Install the outer cowl top panel with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp*2 of the wire harness.
Engage the clamp*1 and connect the connector (w/ Windshield Deicer).
![]() |
Engage the clamp of the wire harness.
| 11. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 12. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 13. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
Install the windshield wiper motor and link assembly (Click here).