LOWER INSTRUMENT PANEL > INSTALLATION |
| 1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD) |
When using a new lower instrument panel sub-assembly:
Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration.

Install the lower instrument panel sub-assembly with the 4 bolts <B>, 11 bolts <C> and screw <D>.

| *1 | Bolt <B> | *2 | Bolt <C> |
| *3 | Screw <D> | - | - |
Engage each clamp.

| 2. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD) |
When using a new lower instrument panel sub-assembly:
Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration.

Install the lower instrument panel sub-assembly with the 4 bolts <B>, 11 bolts <C> and screw <D>.

| *1 | Bolt <B> | *2 | Bolt <C> |
| *3 | Screw <D> | - | - |
Engage each clamp.
Engage the 2 claws.

| 3. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD) |
for Connector Type Antenna Cord:
![]() |
Engage the 4 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the connector.
for Plug Type Antenna Cord:
![]() |
Engage the 5 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the 2 connectors.
| 4. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD) |
for Connector Type Antenna Cord:
![]() |
Engage the 5 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the connector.
for Plug Type Antenna Cord:
![]() |
Engage the 6 clamps.
Install the No. 2 antenna cord sub-assembly with the bolt.
Connect the 2 connectors.
| 5. INSTALL GLOVE BOX LIGHT ASSEMBLY |
![]() |
Engage the 2 claws and install the glove box light assembly.
Connect the connector.
| 6. INSTALL GLOVE COMPARTMENT DOOR LOCK ASSEMBLY |
![]() |
Install the glove compartment door lock assembly with the screw <D>.
| 7. INSTALL INSTRUMENT PANEL SAFETY PAD PLATE SUB-ASSEMBLY (for LHD) |
![]() |
Install the instrument panel safety pad plate sub-assembly with the 2 bolts <B>.
| 8. INSTALL POWER STEERING ECU ASSEMBLY |
![]() |
Install the power steering ECU assembly with the bolt and 2 nuts.
![]() |
Connect the 3 connectors to the power steering ECU assembly.
![]() |
Connect the connector to the power steering ECU assembly.
| *1 | Lock Lever |
| *2 | Lock of the Lock Lever |
Engage the wire harness clamp to the power steering ECU assembly.
| 9. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Engage the clip.
Install the combination meter assembly with the 3 screws.
Engage the clamp.
Connect the 3 connectors.
| 10. INSTALL NO. 1 HEATER TO REGISTER DUCT |
![]() |
Install the No. 1 heater to register duct with the 3 clips.
| 11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 12. INSTALL FRONT DOOR SCUFF PLATE RH |
| 13. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY |
![]() |
Engage the claw to install the glove compartment door stopper sub-assembly.
| 14. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.
| *a | Opened Approximately 55° |
| *b | Closed |
![]() |
Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.
| *1 | Glove Compartment Door Stopper Sub-assembly |
| *2 | Stopper |
Engage the claw and connect the glove compartment door stopper sub-assembly.
| 15. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Connect the connector.
![]() |
Engage the guide and 3 claws to install the No. 2 instrument panel under cover sub-assembly.
| 16. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Connect the airbag connector and install the clamp to the driver side knee airbag assembly.
Push in the lock to install the airbag connector.
![]() |
Temporarily install the driver side knee airbag assembly with the 6 claws and 4 guides.
![]() |
Install the driver side knee airbag assembly with the 4 bolts.
| 17. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD) |
Connect each connector.
![]() |
Engage the guide and claw.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.
| 18. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD) |
Connect each connector.
![]() |
Engage the guide and 2 claws.
Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.
| 19. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Engage the claw and 2 pins to install the upper steering column cover.
| 20. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Engage the 4 claws.
![]() |
Engage the claw.
| 21. INSTALL NO. 1 SWITCH HOLE BASE |
Connect the connector.
![]() |
Engage the 5 claws to install the No. 1 switch hole base.
| 22. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
![]() |
Temporarily install the console box assembly.
![]() |
Engage the 9 claws as shown in the illustration.
![]() |
Install the to install the upper instrument panel finish panel assembly with the 2 bolts <A>.
Engage the clamp.
| 23. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY |
![]() |
Install the shift lock control unit assembly with the 3 nuts.
Connect the connector to the shift lock control unit assembly.
| 24. INSTALL AIR CONDITIONING CONTROL ASSEMBLY |
Connect the connector.
![]() |
Engage the 4 claws to install the air conditioning control assembly.
| 25. INSTALL CONSOLE BOX ASSEMBLY |
Connect each connector.
![]() |
Engage the 4 guides and 2 claws as shown in the illustration.
![]() |
Install the console box assembly with the bolt <B> and 2 clips.
| 26. INSTALL BOX BOTTOM MAT |
![]() |
Engage the fastener to install the box bottom mat.
| 27. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.
| 28. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
![]() |
Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.
| 29. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET |
![]() |
Install the No. 2 console box mounting bracket with the 6 bolts <B>.
| 30. INSTALL ELECTRICAL KEY OSCILLATOR |
![]() |
Engage the clamp and install the electrical key oscillator.
Connect the connector.
| 31. INSTALL REAR CONSOLE BOX ASSEMBLY |
Connect the connector.
![]() |
Engage the 8 claws as shown in the illustration.
![]() |
Install the rear console box assembly with the 5 bolts.
| 32. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 33. INSTALL UPPER CONSOLE PANEL |
![]() |
Engage the 3 claws to install the upper console panel.
| 34. INSTALL REAR CONSOLE BOX POCKET |
![]() |
Install the rear console box pocket as shown in the illustration.
| 35. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY |
Install the upper instrument panel assembly (Click here).
| 36. INSPECT SHIFT LEVER |
Turn the power switch on (READY).
Check that all available shift positions can be selected moving the shift lever.