Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1503    Exhaust Heat Management Warning Detected

for Preparation Click here


DESCRIPTION

This DTC is stored when the combination meter assembly (No. 3 meter circuit plate) detects a malfunction in the water temperature sensor that is connected to the combination meter assembly (No. 3 meter circuit plate) via a direct line.

DTC No.
DTC Detection Condition
Trouble Area
B1503
When IG voltage is 9.5 V or more and the following conditions is detected:
  1. Coolant temperature sensor operation malfunction
  2. Coolant temperature sensor circuit open or short
  3. Engine coolant temperature is 120°C (248°F) or more
  1. Harness or connector
  2. Water temperature sensor
  3. Combination meter assembly (No. 3 meter circuit plate)

HINT:
This DTC is for the water temperature sensor which is used to detect the engine water temperature sensor for the exhaust heat recirculation system, not for the engine coolant temperature sensor which is used for the EFI system.


WIRING DIAGRAM


E188188E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Set the vehicle in the maintenance mode using the intelligent tester (Click here).

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F)
    After warming up: 80 to 100°C (176 to 212°F)
    1. If -40°C (-40°F): Sensor circuit open
    2. If 140°C (284°F) or more: Sensor circuit shorted

    OK:
    Engine coolant temperature displayed on the intelligent tester is 80 to 100°C (176 to 212°F) after warming up



NG
GO TO EXHAUST HEAT RECIRCULATION SYSTEM (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - WATER TEMPERATURE SENSOR)
  1. Disconnect the G2 connector.

  1. Disconnect the L27 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G2-2 (TWS3) - L27-16 (TWS3)
    Always
    Below 1 Ω
    G2-1 (E2) - L27-9 (E2)
    Always
    Below 1 Ω
    G2-2 (TWS3) or L27-16 (TWS3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.WATER TEMPERATURE SENSOR


    E188251E01
  1. Remove the water temperature sensor (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E2) - 2 (TWS3)
    Temperature is 20 °C (68°F)
    2.32 to 2.59 kΩ
    1 (E2) - 2 (TWS3)
    Temperature is 80 °C (176°F)
    0.310 to 0.326 kΩ



NG
REPLACE WATER TEMPERATURE SENSOR (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (NO. 3 METER CIRCUIT PLATE)