Home › Vehicle Interior › HEATING / AIR CONDITIONING › SOLAR VENTILATION ECU

SOLAR VENTILATION ECU > REMOVAL

for Preparation Click here



1. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



6. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    B223452E01
  1. Using a moulding remover, slightly lift the panel at the position shown in the illustration.
    Text in Illustration 
    *a
    Lift slightly

  1. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

  1. Disconnect each connector and remove the integration control and panel assembly.



7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B223454
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.



    B223455
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.



8. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Disengage the 14 claws.



  1. Disconnect the connector and remove the instrument cluster finish panel garnish.


    B223458



9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B223459
  1. Disengage the 3 claws.

  1. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.



10. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    B227341
  1. Disengage the 4 claws and remove the center instrument cluster finish panel sub-assembly.



11. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    B223593
  1. Remove the 4 bolts <B> and radio tuner opening cover with bracket.



12. REMOVE RADIO RECEIVER WITH BRACKET (w/o Navigation System)


    E188506
  1. Remove the 4 bolts.



    E188509
  1. Disengage the 4 claws as shown in the illustration.

  1. Disconnect each connector and remove the radio receiver with bracket.



13. REMOVE NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)


    E188505
  1. Remove the 4 bolts.



    E188507
  1. Disengage the 4 claws and remove the navigation receiver assembly with bracket as shown in the illustration.

  1. Disconnect each connector.



14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E189053
  1. Disengage the 4 claws and remove the air conditioning control assembly as shown in the illustration.

  1. Disconnect the connector.

    NOTICE:
    Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, mark them so that they will not be reconnected incorrectly.



15. REMOVE SOLAR VENTILATION ECU


    E189041
  1. Remove the bolt.

  1. Disconnect the connector to remove the solar ventilation ECU.