Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST PRE SUPPORT SWITCH

PARKING ASSIST PRE SUPPORT SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL PARKING ASSIST PRE SUPPORT SWITCH


    E186358
  1. Engage the 2 claws to install the parking assist pre support switch.



2. INSTALL NO. 1 SWITCH HOLE BASE
  1. Connect the connector.



    B223657
  1. Engage the 5 claws to install the No. 1 switch hole base.



3. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B223656
  1. Temporarily install the console box assembly.



    B231088
  1. Engage the 9 claws as shown in the illustration.



    B223654
  1. Install the to install the upper instrument panel finish panel assembly with the 2 bolts <A>.

  1. Engage the clamp.



4. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY


    C209262
  1. Install the shift lock control unit assembly with the 3 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the connector to the shift lock control unit assembly.



5. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
  1. Connect the connector.

    NOTICE:
    Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, take care to connect each connector to the correct component.



    E189054
  1. Engage the 4 claws to install the air conditioning control assembly.



6. INSTALL CONSOLE BOX ASSEMBLY
  1. Connect each connector.



    B223653
  1. Engage the 4 guides and 2 claws as shown in the illustration.



    B223651
  1. Install the console box assembly with the bolt <B> and 2 clips.



7. INSTALL BOX BOTTOM MAT


    B233780
  1. Engage the fastener to install the box bottom mat.



8. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B223646E01
  1. Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.



9. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    B223644E01
  1. Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.



10. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET


    B223617
  1. Install the No. 2 console box mounting bracket with the 6 bolts <B>.



11. INSTALL ELECTRICAL KEY OSCILLATOR


    B229283
  1. Engage the clamp and install the electrical key oscillator.

    NOTICE:
    Be careful when installing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.

  1. Connect the connector.



12. INSTALL REAR CONSOLE BOX ASSEMBLY
  1. Connect the connector.



    B223616
  1. Engage the 8 claws as shown in the illustration.



    B223614
  1. Install the rear console box assembly with the 5 bolts.



13. INSTALL CONSOLE BOX CARPET


    B223613
  1. Install the console box carpet.



14. INSTALL UPPER CONSOLE PANEL


    B223612
  1. Engage the 3 claws to install the upper console panel.



15. INSTALL REAR CONSOLE BOX POCKET


    B223610
  1. Install the rear console box pocket as shown in the illustration.



16. INSTALL NAVIGATION RECEIVER WITH BRACKET


    E188508
  1. Engage the 4 claws to temporarily install the navigation receiver assembly with bracket as shown in the illustration.



    E188505
  1. Install the navigation receiver assembly with bracket with the 4 bolts.



17. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B223459
  1. Connect the connector.

  1. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.



18. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Connect the connector.



  1. Engage the 14 claws to install the instrument cluster finish panel garnish.


    B223458



19. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B223456
  1. Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.



20. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    B223453
  1. Connect each connector.

  1. Engage the 6 claws to install the integration control and panel assembly.



21. INSPECT SHIFT LEVER
  1. Turn the power switch on (READY).

  1. Check that all available shift positions can be selected moving the shift lever.

    HINT:
    After the shift lever is replaced with a new one, perform the above operation. If this operation is not performed, moving the shift lever may not initially select shift positions.