PARKING ASSIST PRE SUPPORT SWITCH > REMOVAL |
| 1. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Using a moulding remover, slightly lift the panel at the position shown in the illustration.
| *a | Lift slightly |
Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.
Disconnect each connector and remove the integration control and panel assembly.
| 2. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.
![]() |
Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.
| 3. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Disengage the 14 claws.
Disconnect the connector and remove the instrument cluster finish panel garnish.

| 4. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
![]() |
Disengage the 3 claws.
Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.
| 5. REMOVE NAVIGATION RECEIVER WITH BRACKET |
![]() |
Remove the 4 bolts.
![]() |
Disengage the 4 claws and remove the navigation receiver with bracket as shown in the illustration.
Disconnect each connector.
| 6. REMOVE REAR CONSOLE BOX CUP HOLDER |
![]() |
Disengage the 4 claws and remove the rear console box cup holder as shown in the illustration.
| 7. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 8. REMOVE REAR CONSOLE BOX ASSEMBLY |
![]() |
Remove the 5 bolts.
![]() |
Pull the rear console box assembly in the direction indicated by the arrow to disengage the 8 claws.
Disconnect each connector and remove the rear console box assembly.
| 9. REMOVE ELECTRICAL KEY OSCILLATOR |
![]() |
Disconnect the connector.
Disengage the clamp and remove the electrical key oscillator.
| 10. REMOVE NO. 2 CONSOLE BOX MOUNTING BRACKET |
![]() |
Remove the 6 bolts <B> and No. 2 console box mounting bracket.
| 11. REMOVE FRONT NO. 1 CONSOLE BOX INSERT |
![]() |
Pull the front No. 1 console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the front No. 1 console box insert.
| 12. REMOVE FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Pull the front No. 2 console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the front No. 2 console box insert.
| 13. REMOVE BOX BOTTOM MAT |
![]() |
Disengage the fastener and remove the box bottom mat.
| 14. SEPARATE CONSOLE BOX ASSEMBLY |
![]() |
Remove the bolt <B> and 2 clips.
![]() |
While pushing the parts shown in the illustration inward, pull the console box assembly in the direction indicated by the arrow to disengage the 2 claws and 4 guides.
Disconnect the connector and separate the console box assembly.
| 15. REMOVE AIR CONDITIONING CONTROL ASSEMBLY |
![]() |
Disengage the 4 claws and remove the air conditioning control assembly as shown in the illustration.
Disconnect the connector.
| 16. REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY |
![]() |
Disconnect the connector from the shift lock control unit assembly.
Remove the 3 nuts and shift lock control unit assembly.
| 17. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
![]() |
Disengage the clamp.
Remove the 2 bolts <A>.
![]() |
Pull the upper instrument panel finish panel assembly in the direction indicated by the arrow to disengage the 9 claws and remove the upper instrument panel finish panel assembly.
| 18. REMOVE CONSOLE BOX ASSEMBLY |
![]() |
Remove the console box assembly.
| 19. REMOVE NO. 1 SWITCH HOLE BASE |
![]() |
Disengage the 5 claws.
Disconnect the connector to remove the No. 1 switch hole base.
| 20. REMOVE PARKING ASSIST PRE SUPPORT SWITCH |
![]() |
Disengage the 2 claws and remove the parking assist pre support switch.