BRAKE BOOSTER PUMP > REMOVAL |
| 1. PRECAUTION (w/ Navigation System for HDD) |
| 2. REMOVE REAR NO. 2 FLOOR BOARD (for RHD) |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 3. REMOVE REAR DECK FLOOR BOX (for RHD) |
Remove the rear deck floor box.
| 4. REMOVE REAR NO. 3 FLOOR BOARD (for RHD) |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 5. DISABLE BRAKE CONTROL (for RHD) |
Wait at least 2 minutes after the power switch off.
![]() |
Disconnect the reservoir level switch connector with the parking brake applied.
Disconnect the cable from the negative (-) battery terminal.
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal can not be further depressed.
Release the parking brake.
| 6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD) |
| 7. REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for RHD) |
![]() |
Remove the 3 bolts and cowl body mounting reinforcement LH.
| 8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the clamp and separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Disengage the clamp*1 and disconnect the connector (w/ Windshield Deicer).
Disengage the clamp*2 and separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Disengage the claw and bend the No. 1 heater air duct splash shield seal.
![]() |
Disengage the claw and bend the water guard plate RH.
![]() |
Remove the 9 bolts and outer cowl top panel sub-assembly.
| 9. DRAIN BRAKE FLUID (for RHD) |
| 10. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for LHD) |
| 11. REMOVE FRONT CROSS MEMBER SUB-ASSEMBLY |
| 12. REMOVE NO. 5 BRAKE ACTUATOR BRACKET |
![]() |
Remove the 2 nuts and No. 5 brake actuator bracket.
Separate the wire harness clamp.
| 13. REMOVE BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET |
![]() |
Disconnect the 2 connectors and separate the clamp from the brake booster pump assembly.
![]() |
Remove the clip and brake actuator hose.
| *1 | Brake Actuator Hose |
| *2 | No. 2 Brake Tube Clamp |
| *3 | No. 1 Brake Tube Clamp |
| *4 | Front No. 1 Brake Tube |
Remove the 2 bolts, No. 1 brake tube clamp and No. 2 brake tube clamp.
Disconnect the front No. 1 brake tube.
![]() |
Separate the wire harness clamp, 2 fuel lines and front No. 4 brake tube from the brake booster pump assembly.
| *1 | Wire Harness Clamp |
| *2 | Fuel Line |
| *3 | Front No. 4 Brake Tube |
![]() |
Remove the 3 nuts and brake booster pump assembly with bracket.
| 14. REMOVE BRAKE BOOSTER PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, brake booster pump bushings, brake actuator case collars and brake booster pump assembly from the brake actuator bracket assembly.
| *1 | Nut |
| *2 | Brake Actuator Case Collar |
| *3 | Brake Booster Pump Bushing |
| *4 | Brake Actuator Bracket Assembly |
| *5 | Brake Booster Pump Assembly |