Home › Steering › STEERING COLUMN › STEERING PAD SWITCH

STEERING PAD SWITCH > INSPECTION

for Preparation Click here



1. INSPECT STEERING PAD SWITCH ASSEMBLY (Before October, 2010)


  1. Measure the resistance according to the value(s) in the table below.


    E170012E01


    Standard Resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    z9-1 (HO) - Terminal A
    Always
    Below 1 Ω
    z9-3 (AC1) - z9-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z9-3 (AC1) - z9-8 (EAU)
    R/F switch: ON
    323 to 335 Ω
    z9-3 (AC1) - z9-8 (EAU)
    TEMP+ switch: pushed
    980 to 1020 Ω
    z9-3 (AC1) - z9-8 (EAU)
    TEMP- switch: pushed
    3048 to 3172 Ω
    z9-4 (DIST) - z9-6 (ECC)
    Distance control switch: ON
    Below 2.5 Ω
    z9-4 (DIST) - z9-6 (ECC)
    No switch pushed
    1 MΩ or higher
    z9-9 (AU2) - z9-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z9-9 (AU2) - z9-8 (EAU)
    MODE switch: pushed
    Below 2.5 Ω
    z9-9 (AU2) - z9-8 (EAU)
    Voice switch: pushed
    3048 to 3172 Ω
    z9-9 (AU2) - z9-8 (EAU)
    On Hook switch: pushed
    323 to 335 Ω
    z9-9 (AU2) - z9-8 (EAU)
    Off Hook switch: pushed
    980 to 1020 Ω
    z9-10 (AU1) - z9-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z9-10 (AU1) - z9-8 (EAU)
    Seek+ switch: pushed
    Below 2.5 Ω
    z9-10 (AU1) - z9-8 (EAU)
    Seek- switch: pushed
    323 to 335 Ω
    z9-10 (AU1) - z9-8 (EAU)
    Volume+ switch: pushed
    980 to 1020 Ω
    z9-10 (AU1) - z9-8 (EAU)
    Volume- switch: pushed
    3048 to 3172 Ω

    HINT:
    If the result is not as specified, replace the steering pad switch assembly.


    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch Assembly)
    *2
    Volume+
    *3
    Volume-
    *4
    MODE
    *5
    Seek-
    *6
    Seek+
    *7
    Voice switch
    *8
    On Hook
    *9
    Off Hook
    *10
    TRIP switch
    *11
    DISP switch
    *12
    R/F switch
    *13
    TEMP-
    *14
    TEMP+
    *15
    Distance control switch
    *16
    Terminal-A



  1. Check the illumination


    E194898E01


    1. Connect a positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      HINT:
      If the result is not as specified, replace the steering pad switch assembly.


      Text in Illustration 
      *1
      Component without harness connected
      (Steering Pad Switch Assembly)



2. INSPECT STEERING PAD SWITCH LH (From October, 2010)


  1. Measure the resistance according to the value(s) in the table below.


    E254394E04

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (AU1) - 4 (EAU)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    323 to 335 Ω
    Volume+ switch pushed
    980 to 1020 Ω
    Volume- switch pushed
    3048 to 3172 Ω
    2 (AU2) - 4 EAU)
    No switch pushed
    95 to 105 kΩ
    MODE switch pushed
    Below 2.5 Ω
    On hook switch pushed
    323 to 335 Ω
    Off hook switch pushed
    980 to 1020 Ω
    Voice switch pushed
    3048 to 3172 Ω

    HINT:
    If the result is not as specified, replace the steering pad switch LH.


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch LH)
    *b
    Volume+
    *c
    Volume-
    *d
    MODE
    *e
    Seek+
    *f
    Seek-
    *g
    Voice
    *h
    On hook
    *i
    Off hook
    -
    -



  1. Check the illumination.


    E254395E01


    1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch LH connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      HINT:
      If the result is not as specified, replace the steering pad switch LH.


      Text in Illustration 
      *a
      Component without harness connected
      (Steering Pad Switch LH)
      -
      -



3. INSPECT STEERING PAD SWITCH RH (From October, 2010)


  1. Measure the resistance according to the value(s) in the table below.


    E256156E01

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-1 (HO) - Terminal-A
    Always
    Below 1 Ω
    z9-3 (AC1) - z9-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    R/F switch pushed
    323 to 335 Ω
    TEMP+ switch pushed
    980 to 1020 Ω
    TEMP- switch pushed
    3048 to 3172 Ω
    z9-4 (DIST) - z9-6 (ECC)
    No switch pushed
    1 MΩ or higher
    Distance control switch pushed
    Below 2.5 Ω
    SR1-3 (IL+2) - z9-5 (IL+2)
    Always
    Below 1 Ω
    SR1-1 (AU1) - z9-10 (AU1)
    Always
    Below 1 Ω
    SR1-2 (AU2) - z9-9 (AU2)
    Always
    Below 1 Ω
    SR1-4 (EAU) - z9-8 (EAU)
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, replace the steering pad switch RH.


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch RH)
    *b
    TEMP+
    *c
    TEMP-
    *d
    DISP
    *e
    R/F
    *f
    TRIP
    *g
    Distance control
    *h
    Terminal-A



  1. Check the illumination.


    E256157E01


    1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch RH connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      HINT:
      If the result is not as specified, replace the steering pad switch RH.


      Text in Illustration 
      *a
      Component without harness connected
      (Steering Pad Switch RH)
      -
      -