Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM

BLOCKING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TELEPHONE TRANSCEIVER ASSEMBLY


  1. Disconnect the L156 telephone transceiver assembly connector.


    B319602E09

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L156-6 (IG2) - L156-9 (E)
    L - BR
    Ignition power supply
    Power switch on (IG)
    9 to 16 V
    L156-12 (+B) - L156-9 (E)
    SB - BR
    +B power supply
    Power switch off
    9 to 16 V
    L156-9 (E) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the L156 telephone transceiver assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L156-1 (BLK1) - L156-9 (E)
    L - BR
    ID code box (immobiliser code ECU) communication input
    Power switch off
    11 to 14 V
    L156-1 (BLK1) - L156-9 (E)
    L - BR
    ID code box (immobiliser code ECU) communication input
    Within 3 seconds of power switch on (READY), or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    L156-2 (BLK4) - L156-9 (E)
    R - BR
    ID code box (immobiliser code ECU) communication output
    Power switch off
    Below 1 V
    L156-2 (BLK4) - L156-9 (E)
    R - BR
    ID code box (immobiliser code ECU) communication output
    Within 3 seconds of power switch on (READY), or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)
    L156-7 (BLK2) - L156-9 (E)
    L -BR
    Power management control ECU (HV CPU) communication output
    Power switch off
    Below 1 V
    L156-7 (BLK2) - L156-9 (E)
    L - BR
    Power management control ECU (HV CPU) communication output
    Within 3 seconds of power switch on (READY), or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    L156-8 (BLK3) - L156-9 (E)
    R - BR
    Power management control ECU (HV CPU) communication input
    Power switch off
    Below 1 V
    L156-8 (BLK3) - L156-9 (E)
    R - BR
    Power management control ECU (HV CPU) communication input
    Within 3 seconds of power switch on (READY), or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)

    1. If the result is not as specified, the telephone transceiver assembly may have a malfunction.



  5. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B253467E05


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 510 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      1. L156-1 (BLK1) - L156-9 (E)
      2. L156-7 (BLK2) - L156-9 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of power switch on (READY), or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected



    2. Waveform 2 (Reference)


      B253466E04


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 510 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      1. L156-2 (BLK4) - L156-9 (E)
      2. L156-8 (BLK3) - L156-9 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of power switch on (READY), or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


CHECK ID CODE BOX (IMMOBILISER CODE ECU)


  1. Disconnect the L10 ID code box (immobiliser code ECU) connector.


    B118534E49

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-1 (+B) - L10-8 (GND)
    B - W-B
    +B power supply
    Power switch off
    11 to 14 V
    L10-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L10 ID code box (immobiliser code ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-5 (EFII) - L10-8 (GND)
    L - W-B
    Power management control ECU (HV CPU) input signal
    Power switch off
    11 to 14 V
    L10-5 (EFII) - L10-8 (GND)
    L - W-B
    Power management control ECU (HV CPU) input signal
    Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after auxiliary battery disconnected and connected
    Pulse generation
    (See waveform 1)
    L10-6 (EFIO) - L10-8 (GND)
    R - W-B
    Power management control ECU (HV CPU) output signal
    Power switch off
    Below 1 V
    L10-6 (EFIO) - L10-8 (GND)
    R - W-B
    Power management control ECU (HV CPU) output signal
    Power switch on (IG)
    Pulse generation
    (See waveform 2)

    1. If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.



  5. Inspect using an oscilloscope.



    1. Waveform 1 (Reference)


      B253467E05


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 510 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      L10-5 (EFII) - L10-8 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after auxiliary battery disconnected and connected



    2. Waveform 2 (Reference)


      B253466E04


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 510 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      L10-6 (EFIO) - L10-8 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Power switch on (IG)


CHECK POWER MANAGEMENT CONTROL ECU (HV CPU)


  1. Disconnect the L5 power management control ECU (HV CPU) connector.


    B219312E02

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L5-6 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L5 power management control ECU (HV CPU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L6-20 (IMO) - L5-6 (E1)
    L - BR
    ID code box (immobiliser code ECU) input signal
    Power switch off
    11 to 14 V
    L6-20 (IMO) - L5-6 (E1)
    L - BR
    ID code box (immobiliser code ECU) input signal
    Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after auxiliary battery disconnected and connected
    Pulse generation
    (See waveform 1)
    L6-21 (IMI) - L5-6 (E1)
    R - BR
    ID code box (immobiliser code ECU) output signal
    Power switch off
    Below 1 V
    L6-21 (IMI) - L5-6 (E1)
    R - BR
    ID code box (immobiliser code ECU) output signal
    Power switch on (IG)
    Pulse generation
    (See waveform 2)
    If the result is not as specified, the power management control ECU (HV CPU) may have a malfunction.



  5. Waveform:



    1. Waveform 1 (Reference)


      B253467E05


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 510 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      L6-20 (IMO) - L5-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after auxiliary battery disconnected and connected



    2. Waveform 2 (Reference)


      B253466E04


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 510 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      L6-21 (IMI) - L5-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Power switch on (IG)