FRONT SEAT SIDE AIRBAG ASSEMBLY > INSTALLATION |
| 1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY |
Install the front seat side airbag assembly with 2 new nuts.
Engage the 2 clamps.
| 2. INSTALL FRONT SEATBACK COVER WITH PAD (for Manual Seat) |
![]() |
Install the front seatback cover bracket with the nut.
![]() |
Engage the 4 claws and install the 2 front seat headrest supports.
![]() |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 3 new hog rings.
| 3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat) |
Temporarily install the separate type front seatback cover with pad to the front seatback spring sub-assembly.
![]() |
Engage the 4 claws and install the 2 front seat headrest supports.
![]() |
Install the separate type front seatback cover bracket with the nut.
![]() |
Engage the 2 hooks.
![]() |
Using hog ring pliers, install the fastening rubber to the front seatback spring with 3 new hog rings.
| *1 | Fastening Rubber |
![]() |
Close the 2 fasteners.
![]() |
Push in the lower part of 2 fasteners to the separate type front seatback cover as shown in the illustration.
![]() |
Using hog ring pliers, install 3 new hog rings.
![]() |
Using hog ring pliers, install 2 new hog rings.
| 4. CONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY WIRE HARNESS |
for Manual Seat:
![]() |
Using hog ring pliers, install 3 new hog rings.
Engage the fastener to secure the front seat side airbag assembly wire harness.
w/ Seat Heater System:
Engage the clamp and connect the seat heater wire harness connector.
Connect the front seat side airbag assembly wire harness to the seat clamp.
Engage the claw and 3 clamps to install the front seat side airbag assembly wire harness.
Connect the rubber band.
| 5. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat) |
Place the front seat assembly in the cabin.
Connect the connectors under the seat.
Temporarily install the front seat assembly with the 4 bolts.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
Lift up the seat track adjusting handle and move the seat to the foremost position.
![]() |
Tighten the 2 bolts on the rear side of the seat.
| 6. INSTALL FRONT SEAT ASSEMBLY (for Power Seat) |
Place the front seat assembly in the cabin.
Connect the connectors under the seat.
Connect the cable to the auxiliary negative (-) battery terminal.
Temporarily install the front seat assembly with the 4 bolts.
Operate the power seat switch knob and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
Operate the power seat switch knob and move the seat to the foremost position.
![]() |
Tighten the 2 bolts on the rear side of the seat.
| 7. INSTALL INNER SEAT TRACK COVER (for Manual Seat) |
![]() |
Engage the claw and guide and install the inner seat track cover.
| 8. INSTALL INNER SEAT TRACK COVER (for Power Seat) |
Engage the 2 claws to install the inner seat track cover.
| 9. INSTALL OUTER SEAT TRACK COVER (for Manual Seat) |
![]() |
Engage the 2 claws and install the outer seat track cover.
| 10. INSTALL OUTER SEAT TRACK COVER (for Power Seat) |
Engage the 2 claws to install the outer seat track cover.
| 11. INSTALL FRONT SEAT HEADREST ASSEMBLY |
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat) |
| 13. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 14. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 15. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 16. INSPECT FRONT SEAT ASSEMBLY (for Manual Seat) |
During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
If the seat adjusters do not lock simultaneously, loosen the seat mounting bolts to adjust the adjuster position.
w/ Seat Heater Seat System:
Check the seat heater operation.
Turn the power switch on (IG).
Push the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 17. INSPECT FRONT SEAT ASSEMBLY (for Power Seat) |
Check the power seat operation (Click here).
Check the seat heater operation.
Turn the power switch on.
Turn the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 18. PERFORM DIAGNOSTIC SYSTEM CHECK |
| 19. INSPECT SRS WARNING LIGHT |