Home › Drivetrain › P410 HYBRID TRANSMISSION / TRANSAXLE › HYBRID VEHICLE TRANSAXLE UNIT

HYBRID VEHICLE TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here


NOTICE:
  1. Do not use gloves, cloths or papers that produce lint or dust.
  2. Cover the removed parts with plastic bags to prevent entry of foreign matter.

  3. Do not remove the generator cable terminal, motor cable terminal, transaxle housing cover, rear transaxle case cover sub-assembly or resolver adjuster bolts.


    C270631E01


    Text in Illustration 
    *1
    Generator Cable Terminal
    *2
    Motor Cable Terminal
    *3
    Transaxle Housing Cover
    *4
    Rear Transaxle Case Cover Sub-assembly
    *5
    Resolver Adjuster Bolt
    -
    -



1. INSPECT INPUT SHAFT END PLAY


    C269194E01
  1. Using a SST and dial indicator, measure the input shaft assembly end play.

    SST
    09951-01600  

    Standard end play:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    If the value is not as specified, replace the planetary sun gear snap ring with one of the correct thickness.



2. REMOVE GENERATOR CABLE


    C209803
  1. Remove the 3 bolts and slide the generator cable connector shell back.



    C209805
  1. Disengage the 2 claws to remove the terminal cap from the hybrid vehicle transaxle assembly.



    C209806
  1. Remove the 3 bolts and generator cable from the hybrid vehicle transaxle assembly.

    NOTICE:
    Keep foreign matter, water, etc. away from the terminal cable and its installation section.



3. REMOVE MOTOR CABLE


    C209808
  1. Remove the 3 bolts and slide the motor cable connector shell back.



    C209810
  1. Disengage the 2 claws to remove the terminal cap from the hybrid vehicle transaxle assembly.



    C209811
  1. Remove the 3 bolts and motor cable from the hybrid vehicle transaxle assembly.

    NOTICE:
    Keep foreign matter, water, etc. away from the terminal cable and its installation section.



4. REMOVE SHIFT CONTROL ACTUATOR ASSEMBLY


    C269277
  1. Remove the 3 shift control actuator bolts and shift control actuator assembly from the hybrid vehicle transaxle assembly.

    HINT:
    1. Please refer to Service Bulletin for details on the removal procedure of the shift control actuator bolt.
    2. This actuator is a precision instrument. Do not strike it with a plastic hammer or the like during installation.
    3. This actuator detects its own position when a battery is reinstalled. Thus it does not require initialization.



5. REMOVE TRANSAXLE BREATHER PLUG


    C268191
  1. Remove the transaxle breather plug from the hybrid vehicle transaxle assembly.

    NOTICE:
    Be careful not to damage the transaxle breather plug.



6. REMOVE WITH HEAD STRAIGHT SCREW PLUG


    C271765
  1. Using a 6 mm hexagon socket wrench, remove the 2 with head straight screw plugs from the hybrid vehicle transaxle assembly.



7. REMOVE TRANSMISSION OIL PUMP COVER SUB-ASSEMBLY


    C209292
  1. Remove the fluid pump cover plug and O-ring from the transmission oil pump cover sub-assembly.



    C268195
  1. Remove the 4 bolts and transmission oil pump cover sub-assembly from the hybrid vehicle transaxle assembly.

    NOTICE:
    Do not drop the transaxle oil pump drive rotor or transmission oil pump driven rotor.



    C268200E01
  1. Remove the transaxle oil pump drive rotor and transmission oil pump driven rotor from the hybrid vehicle transaxle assembly.
    Text in Illustration 
    *1
    Transaxle Oil Pump Drive Rotor
    *2
    Transmission Oil Pump Driven Rotor



    C268196
  1. Remove the O-ring from the hybrid vehicle transaxle assembly.



8. REMOVE OIL PUMP DRIVE SHAFT


    C268201
  1. Remove the oil pump drive shaft from the hybrid vehicle transaxle assembly.



9. SECURE HYBRID VEHICLE TRANSAXLE ASSEMBLY


    C268203E01
  1. Place wooden blocks under the hybrid vehicle transaxle assembly.
    Text in Illustration 
    *1
    Wooden Block
    *2
    Resolver Sensor Connector
    *a
    Installation area of the Transmission Oil Pump Cover Sub-assembly
    V100155
    Wooden Block Placement Position

    NOTICE:
    Do not place the wooden blocks under the installation area of the transmission oil pump cover sub-assembly or resolver sensor connector.



10. REMOVE FILLER PLUG


    C268204
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly.



11. REMOVE DRAIN PLUG


    C268205
  1. Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly.



12. REMOVE NO. 1 MOTOR WATER JACKET COVER ASSEMBLY


    C268206
  1. Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the No. 1 motor water jacket cover assembly.



    C268207
  1. Remove the 6 bolts from the No. 1 motor water jacket cover assembly.



    C268208E01
  1. Using a screwdriver, remove the No. 1 motor water jacket cover assembly from the hybrid vehicle transaxle assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the hybrid vehicle transaxle assembly.

    HINT:
    Tape the screwdriver tip before use.



13. REMOVE NO. 2 MOTOR WATER JACKET COVER ASSEMBLY


    C268209
  1. Remove the 6 bolts from the No. 2 motor water jacket cover assembly.



    C268210E01
  1. Using a screwdriver, remove the No. 2 motor water jacket cover assembly from the hybrid vehicle transaxle assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the hybrid vehicle transaxle assembly.

    HINT:
    Tape the screwdriver tip before use.



14. REMOVE HYBRID VEHICLE GENERATOR ASSEMBLY


  1. Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts and washer as shown in the illustration.


    C268271E01


    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger
    *3
    Washer
    -
    -

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    Part Name
    Part No.
    No. 1 Engine Hanger
    12281-37050
    No. 2 Engine Hanger
    12282-37040
    Bolt
    91552-81050

    HINT:
    When installing the No. 1 engine hanger, use a washer with an appropriate thickness so that the No. 1 engine hanger will not interfere with the installation surface of the transaxle housing.



    C268211
  1. Remove the 8 bolts from the hybrid vehicle generator assembly.



    C268212
  1. Remove the 8 bolts from the hybrid vehicle generator assembly.

  1. Remove the 2 bolts from the hybrid vehicle motor assembly.



    C268213
  1. While lifting the hybrid vehicle generator assembly with a chain, tap the areas shown in the illustration with a plastic hammer and separate the hybrid vehicle generator assembly from the hybrid vehicle motor assembly.

  1. While lifting the hybrid vehicle generator assembly with a chain, remove it from the hybrid vehicle motor assembly.

    NOTICE:
    1. Lift the hybrid vehicle generator assembly straight up.
    2. If the hybrid vehicle generator assembly is tilted, return it to the original position before removing.

  1. Remove the 2 bolts, washer, No. 1 engine hanger and No. 2 engine hanger from the hybrid vehicle generator assembly.



15. REMOVE TRANSAXLE HOUSING OIL SEPARATOR


    C268270
  1. Remove the 2 bolts and transaxle housing oil separator from the hybrid vehicle generator assembly.



16. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL (for RH Side)


    C268214E01
  1. Using SST and a hammer, remove the hybrid vehicle transaxle assembly type T oil seal from the hybrid vehicle generator assembly.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07200)



17. REMOVE TAPERED ROLLER BEARING (RH SIDE OUTER RACE)


    C268215
  1. Using brass bar and a hammer, remove the tapered roller bearing (RH side outer race) and shim from the hybrid vehicle generator assembly.

    NOTICE:
    Be careful not to damage the hybrid vehicle generator assembly.



18. REMOVE INPUT SHAFT TYPE T OIL SEAL


    C268216E01
  1. Using SST, remove the input shaft type T oil seal from the hybrid vehicle generator assembly.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09310-36021  

    NOTICE:
    1. Be careful not to damage the hybrid vehicle generator assembly.
    2. When removing the hybrid vehicle generator assembly, be sure to replace the input shaft type T oil seal.



19. REMOVE COUNTER DRIVEN GEAR SHIM


    C268218
  1. Remove the counter driven gear shim from the counter driven gear sub-assembly.



20. REMOVE PARKING LOCK PAWL


    C268219
  1. Remove the parking lock pawl and parking lock pawl shaft from the hybrid vehicle motor assembly.



21. REMOVE PAWL STOPPER PLATE


    C268220
  1. Remove the 2 bolts and pawl stopper plate from the hybrid vehicle motor assembly.



22. REMOVE TORSION SPRING


    C268221
  1. Remove the parking lock pawl shaft and torsion spring from the hybrid vehicle motor assembly.



23. REMOVE PARKING LOCK SLEEVE


    C268222
  1. Remove the parking lock sleeve from the hybrid vehicle motor assembly.



24. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    C268223
  1. Remove the bolt and manual detent spring sub-assembly from the hybrid vehicle motor assembly.



25. REMOVE RETAINER SPRING


    C268224
  1. Remove the retainer spring from the hybrid vehicle motor assembly and No. 1 parking lock shaft.



26. REMOVE NO. 1 PARKING LOCK SHAFT


    C268225
  1. Using a hammer and a screwdriver, cut off the spacer and remove it from the No. 1 parking lock shaft.



    C268226
  1. Using a 5 mm pin punch and a hammer, drive out the slotted spring pin from the No. 1 parking lock shaft.



    C268227
  1. Remove the No. 1 parking lock shaft from the hybrid vehicle motor assembly.



27. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    C268228E01
  1. Remove the No. 1 parking lock lever sub-assembly and parking lock rod sub-assembly from the hybrid vehicle motor assembly.
    Text in Illustration 
    *1
    No. 1 Parking Lock Lever Sub-assembly
    *2
    Parking Lock Rod Sub-assembly



    C268229
  1. Remove the parking lock rod sub-assembly from the No. 1 parking lock lever sub-assembly.



28. REMOVE NO. 1 TRANSMISSION MAGNET


    C268230
  1. Remove the No. 1 transmission magnet from the hybrid vehicle motor assembly.



29. REMOVE INPUT SHAFT ASSEMBLY


    C268231
  1. Remove the input shaft assembly from the counter drive gear sub-assembly.



30. REMOVE PLANETARY SUN GEAR


    C268232E01
  1. Remove the planetary sun gear snap ring and planetary sun gear from the input shaft assembly.
    Text in Illustration 
    *1
    Planetary Sun Gear Snap Ring
    *2
    Planetary Sun Gear



31. REMOVE THRUST NEEDLE ROLLER BEARING


    C268233E01
  1. Remove the thrust bearing race, thrust needle roller bearing and No. 1 thrust bearing race from the input shaft assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing
    *3
    No. 1 Thrust Bearing Race

    HINT:
    The No. 1 thrust bearing race may be attached to the input shaft assembly.



32. REMOVE DIFFERENTIAL CASE SUB-ASSEMBLY


    C268234
  1. Remove the differential case sub-assembly from the hybrid vehicle motor assembly.



33. REMOVE COUNTER DRIVEN GEAR SUB-ASSEMBLY


    C268235
  1. Remove the counter driven gear sub-assembly from the hybrid vehicle motor assembly.



34. REMOVE COUNTER DRIVE GEAR SUB-ASSEMBLY


    C268236
  1. Remove the counter drive gear sub-assembly from the No. 1 rear planetary gear assembly.



35. REMOVE NO. 1 REAR PLANETARY GEAR ASSEMBLY


    C268237
  1. Remove the No. 1 rear planetary gear assembly from the rear planetary sun gear.



36. INSPECT NO. 1 REAR PLANETARY GEAR ASSEMBLY


    C269733
  1. Using a feeler gauge, measure the clearance between the No. 1 rear planetary gear assembly and the pinion gear.

    Standard clearance:
    0.11 to 0.91 mm (0.00433 to 0.0358 in.)

    If the value is not as specified, replace the No. 1 rear planetary gear assembly.



37. REMOVE REAR PLANETARY SUN GEAR


    C268238
  1. Using a snap ring expander, remove the shaft snap ring from the hybrid vehicle motor assembly.



    C268239
  1. Remove the rear planetary sun gear from the hybrid vehicle motor assembly.



38. REMOVE TRANSMISSION OIL STRAINER


    C268240
  1. Remove the bolt and transmission oil strainer from the hybrid vehicle motor assembly.



    C268241
  1. Remove the O-ring from the transmission oil strainer



39. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL (for LH Side)


    C268242E01
  1. Using SST and a hammer, remove the hybrid vehicle transaxle assembly type T oil seal from the hybrid vehicle motor assembly.

    SST
    09950-60010   (09951-00620)
    09950-70010   (09951-07200)



40. REMOVE TAPERED ROLLER BEARING (LH SIDE OUTER RACE)


    C268243
  1. Using brass bar and a hammer, remove the tapered roller bearing (LH side outer race) from the hybrid vehicle motor assembly.

    NOTICE:
    Be careful not to damage the hybrid vehicle motor assembly.



41. REMOVE SHIFT CONTROL ACTUATOR SEAL


    C268244E01
  1. Using a screwdriver, remove the shaft control actuator seal from the hybrid vehicle motor assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the hybrid vehicle motor assembly.

    HINT:
    Tape the screwdriver tip before use.



42. REMOVE TAPERED ROLLER BEARING


  1. Remove tapered roller bearing (LH side):



      C268247E01
    1. Using SST, remove the tapered roller bearing from the differential case sub-assembly.
      Text in Illustration 
      *a
      Hold
      *b
      Turn

      SST
      09950-40011   (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
      09950-60010   (09951-00460)



  1. Remove tapered roller bearing (RH side):



      C268246E01
    1. Using SST, remove the tapered roller bearing from the differential case sub-assembly.
      Text in Illustration 
      *a
      Hold
      *b
      Turn

      SST
      09950-40011   (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
      09950-60010   (09951-00460)



43. REMOVE RADIAL BALL BEARING


  1. Remove radial ball bearing (LH side):



      C268248E01
    1. Using SST, remove the radial ball bearing (LH side) from the counter driven gear sub-assembly.
      Text in Illustration 
      *a
      Hold
      *b
      Turn

      SST
      09950-00020  
      09950-00030  
      09950-40011   (09957-04010)
      09950-60010   (09951-00280)



  1. Remove radial ball bearing (RH side):



      C268249E01
    1. Using SST, remove the radial ball bearing (RH side) from the counter driven gear sub-assembly.
      Text in Illustration 
      *a
      Hold
      *b
      Turn

      SST
      09950-00020  
      09950-00030  
      09950-40011   (09957-04010)
      09950-60010   (09951-00280)



44. REMOVE STRAIGHT PIN


    C268245
  1. Remove the 2 straight pins from the hybrid vehicle motor assembly.