Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3004-131    Power Cable Malfunction

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0AE6-225 .
The power management control ECU monitors the high-voltage wiring between the HV battery and the inverter with converter assembly and detects the following malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3004
131
The inverter voltage does not rise during precharge (time from when SMRP turns on until when SMRG turns on).
  1. Hybrid battery junction block
  2. Frame wire
  3. Inverter with converter assembly
  4. HV battery
  5. Wire harness or connector

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK DTC OUTPUT (HV)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3004-131 only is output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0A1A-151, 155, 156, 658, 659
    Generator Control Module
    P0A1B-164, 193, 512, 661, 786
    Drive Motor "A" Control Module
    P0A1D-148
    Hybrid Powertrain Control Module
    P0A78-266, 267, 586
    Drive Motor "A" Inverter Performance
    P0A94-442
    DC / DC Converter Performance
    P0ADB-227
    Hybrid Battery Positive Contactor Control Circuit Low
    P0ADC-226
    Hybrid Battery Positive Contactor Control Circuit High
    P0ADF-229
    Hybrid Battery Negative Contactor Control Circuit Low
    P0AE0-228
    Hybrid Battery Negative Contactor Control Circuit High
    P0AE6-225
    Hybrid Battery Precharge Contactor Control Circuit Low
    P0AE7-224
    Hybrid Battery Precharge Contactor Control Circuit High
    P0C76-523
    Hybrid Battery System Discharge Time Too Long
    P2511-149
    HV CPU Power Relay Sense Circuit Intermittent No Continuity
    P3004-800, 801
    High Voltage Power Resource
    P324E-788
    MG-ECU Power Relay Intermittent Circuit
    U0110 (all INF codes)*1
    Lost Communication with Drive Motor Control Module "A"

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P3004-131 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


2.CHECK DTC OUTPUT (HV)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3004-131 only is output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0A95-123
    High Voltage Fuse
    P0ABF-123
    Hybrid Battery Pack Current Sensor Circuit
    P0AC0-123
    Hybrid Battery Pack Current Sensor Circuit Range / Performance
    P0AC1-123
    Hybrid Battery Pack Current Sensor Circuit Low
    P0AC2-123
    Hybrid Battery Pack Current Sensor Circuit High
    P0AFC-123
    Hybrid Battery Pack Sensor Module
    P0B3D-123
    Hybrid Battery Voltage Sensor "A" Circuit Low
    P0B42-123
    Hybrid Battery Voltage Sensor "B" Circuit Low
    P0B47-123
    Hybrid Battery Voltage Sensor "C" Circuit Low
    P0B4C-123
    Hybrid Battery Voltage Sensor "D" Circuit Low
    P0B51-123
    Hybrid Battery Voltage Sensor "E" Circuit Low
    P0B56-123
    Hybrid Battery Voltage Sensor "F" Circuit Low
    P0B5B-123
    Hybrid Battery Voltage Sensor "G" Circuit Low
    P0B60-123
    Hybrid Battery Voltage Sensor "H" Circuit Low
    P0B65-123
    Hybrid Battery Voltage Sensor "I" Circuit Low
    P0B6A-123
    Hybrid Battery Voltage Sensor "J" Circuit Low
    P0B6F-123
    Hybrid Battery Voltage Sensor "K" Circuit Low
    P0B74-123
    Hybrid Battery Voltage Sensor "L" Circuit Low
    P0B79-123
    Hybrid Battery Voltage Sensor "M" Circuit Low
    P0B7E-123
    Hybrid Battery Voltage Sensor "N" Circuit Low
    P0B83-123
    Hybrid Battery Voltage Sensor "O" Circuit Low
    P308A-123
    Hybrid Battery Voltage Detection Circuit Open
    U029A-123
    Lost Communication with Hybrid Battery Pack Sensor Module

    HINT:
    P3004-131 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


3.CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read the freeze frame data of DTC P3004-131.

    Result:
    Result
    Proceed to
    Both of the following conditions are met:
    1. Post-boost voltage (VH-Voltage after Boosting) is below 50 V.
    2. Difference between HV battery voltage (Power Resource VB) and pre-boost voltage (VLVoltage before Boosting) is 50 V or less.
    A
    Other than above
    B

  1. Turn the power switch off.



B
Go to step 4
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

4.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


  1. Check the connections of the power management control ECU connectors.


    A220952E01


    Text in Illustration 
    *1
    for LHD
    *2
    for RHD

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


5.CHECK FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY SIDE)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



    A209686
  1. Remove the inverter terminal cover from the inverter with converter assembly.



    A215642E01
  1. Check the connection between the frame wire T1 and the inverter with converter assembly.

    OK:
    The connectors are connected securely and there are no contact problems.

  1. Install the inverter terminal cover to the inverter with converter assembly.



NG
CONNECT SECURELY
OK


6.CHECK FRAME WIRE (HYBRID BATTERY JUNCTION BLOCK SIDE)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).



    A215638E02
  1. Check the connection between the frame wire T4, T3 and the hybrid battery junction block.

Torque:
9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Check for arc marks on the terminals of the frame wire.

    Result:
    Result
    Proceed to
    The terminals are connected securely and there are no contact problems.
    There are no arc marks.
    A
    The terminals are not connected securely and there is a contact problem.
    There are arc marks.
    B
    The terminals are not connected securely and there is a contact problem.
    There are no arc marks.
    C
    The terminals are connected securely and there are no contact problems.
    There are arc marks.
    B

  1. Install the upper hybrid battery cover sub-assembly (Click here).



B
REPLACE MALFUNCTIONING PARTS

C
CONNECT SECURELY
A


7.CHECK FRAME WIRE (INVERTER WITH CONVERTER - HYBRID BATTERY JUNCTION BLOCK)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



    A209686
  1. Remove the inverter terminal cover from the inverter with converter assembly.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).



    A215642E01
  1. Disconnect the frame wire T1 from the inverter with converter assembly.



    A216851E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    T4-1 - T1-2 (CBI)
    Power switch off
    Below 1 Ω
    T3-1 - T1-1 (CEI)
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *1
    Frame Wire (Inverter with Converter Assembly Side)
    *2
    Frame Wire (Hybrid Battery Junction Block Side)
    *3
    Red Mark

  1. Connect the frame wire from the inverter with converter assembly.

  1. Install the upper hybrid battery cover sub-assembly (Click here).

  1. Install the inverter terminal cover to the inverter with converter assembly.



NG
REPLACE FRAME WIRE (Click here)
OK


8.CHECK CONDITION OF MAIN BATTERY CABLE CONNECTION(S)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).



    A215635E01
  1. Check the connections between the main battery cables h2, k2 and the hybrid battery junction block.

    OK:
    The connectors are connected securely and not damaged.

  1. Check for arc marks on the terminals of the main battery cable connectors.

    Result:
    Result
    Proceed to
    The terminals are connected securely and there are no contact problems.
    There are no arc marks.
    A
    The terminals are not connected securely and there is a contact problem.
    There are arc marks.
    B
    The terminals are not connected securely and there is a contact problem.
    There are no arc marks.
    C
    The terminals are connected securely and there are no contact problems.
    There are arc marks.
    B

  1. Install the upper hybrid battery cover sub-assembly (Click here).



B
REPLACE MALFUNCTIONING PARTS

C
CONNECT SECURELY
A


9.CHECK HV BATTERY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).



    A216853E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    h2-1 - 2
    Power switch off
    114 to 190 V
    k2-1 - 1
    Power switch off
    54 to 90 V

    CAUTION:
    Do not allow the probes of the electrical tester to contact each other during this inspection.

  1. Install the upper hybrid battery cover sub-assembly (Click here).



NG
REPLACE HV BATTERY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector L5 from the power management control ECU.

  1. Remove the upper hybrid battery cover sub-assembly (Click here).

  1. Disconnect the connector c3 that drives the relay of the hybrid battery junction block.

    HINT:
    Before disconnecting the connector c3 that drives the relay of the hybrid battery junction block, make sure that the connector is securely engaged.



    A213116E30
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L5-4 (SMRB) - c3-4 (SMRB)
    Power switch off
    Below 1 Ω
    L5-3 (SMRP) - c3-3 (SMRP)
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *2
    Rear view of wire harness connector
    (to Hybrid Battery Junction Block)

  1. Connect the hybrid battery junction block connector.

  1. Install the upper hybrid battery cover sub-assembly (Click here).

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT HYBRID BATTERY JUNCTION BLOCK (SMRB)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the hybrid battery junction block (Click here).



    A215628E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    h2-1 - T4-1
    Auxiliary battery voltage is applied between terminals c3-4 (SMRB) and c3-2 (GND).
    Below 1 Ω

    Text in Illustration 
    *1
    Hybrid Battery Junction Block

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    c3-4 (SMRB) - c3-2 (GND)
    -40 to 80°C (-40 to 176°F)
    19.0 to 35.5 Ω

  1. Install the hybrid battery junction block (Click here).



NG
REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)
OK


12.INSPECT HYBRID BATTERY JUNCTION BLOCK (SMRP)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the hybrid battery junction block (Click here).



    A215628E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    k2-1 - T3-1
    Auxiliary battery voltage is applied between terminals c3-3 (SMRP) and c3-2 (GND).
    28.5 to 31.5 Ω

    Text in Illustration 
    *1
    Hybrid Battery Junction Block

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    c3-3 (SMRP) - c3-2 (GND)
    -40 to 80°C (-40 to 176°F)
    112 to 274 Ω

  1. Install the hybrid battery junction block (Click here).



NG
REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)
OK


13.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).

HINT:
  1. Since 2 trip detection logic is used, the DTC detection condition must be met twice.
  2. If DTC P3004-131 is output again after performing the inspection, replace the hybrid vehicle converter. If DTC P3004-131 is not output again, replace the hybrid battery junction block.



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK

REPLACE HYBRID BATTERY JUNCTION BLOCK (Click here)