SLIDING ROOF SYSTEM > DETAILS



SYSTEM CONTROL


  1. Jam Protection Function



    1. To control the jam protection function, the sliding roof control ECU monitors the amount of movement and judges jamming of the sliding roof based on the pulse signals from the Hall IC1, and the moving direction of the sliding roof from the phase difference between the pulses from Hall IC1 and Hall IC2.


      Y103094E01


FUNCTION
  1. The sliding roof system has following functions:

    Function
    Outline
    Manual Tilt Up
    Tilts up each time the OPEN button on the moonroof switch is pressed for less than approximately 0.3 seconds.
    Manual Open
    Opens from the roof fully tilted up position each time the OPEN button on the moonroof switch is pressed for less than approximately 0.3 seconds.
    Manual Close
    Closes from the roof fully opened position each time the CLOSE button on the moonroof switch is pressed.
    One-touch Auto Tilt Up
    Fully tilts up when the OPEN button on the moonroof switch is pressed for approximately 0.3 seconds or more and less than 1.7 seconds.
    When the OPEN button on the moonroof switch is pressed for approximately 1.7 seconds or more in the tilt-up range, the sliding roof automatically opens after approximately 0.3 seconds since the sliding roof stopped in the fully tilted up position.
    One-touch Auto Open
    Fully opens from the roof fully tilted up position when the OPEN button on the moonroof switch is pressed for approximately 0.3 seconds or more.
    Jam Protection
    The jam protection function automatically stops the sliding roof and moves it open half way (or to the fully tilted up position) if a foreign object gets jammed in the sliding roof during close operation.
    Key-off Operation
    The key-off operation function makes it possible to operate the sliding roof for approximately 43 seconds after the power switch is turned to on (ACC) or off, if the front door is not opened.
    Forced Close Function
    1. The following phenomenon may occur when any foreign object enters the sliding roof or the shade is misaligned. In such cases, the roof can be forcibly closed by pressing the CLOSE button on the moonroof switch for approximately 10 seconds or more.
      1. Stopped again after the roof stopped working due to jam protection while the roof is being closed or tilted.
      2. Stopped immediately before the roof is almost fully closed.
    Sliding Roof Open Warning
    When the power switch is turned from on (IG) to off and the driver door is opened with the sliding roof open, the buzzer in the combination meter assembly sounds once.

    HINT:
    The sliding roof control ECU memorizes the initial position of the sliding roof. This position may disappear from memory or a wrong position might be stored in memory due to some causes such as the disconnection of a battery terminal while the sliding roof is operating. When this occurs, the sliding roof will not operate correctly. For details, see the Repair Manual.


OPERATION


  1. MOONROOF WITH SOLAR PANEL

    1. The front glass panel moves in the tilt up-and-down direction, and the center glass panel moves in the tilt up and open-and-close directions.



    2. The sliding roof motor uses a cable to simultaneously move the 2 (front and center) glass panels. The rear glass panel does not move.


      Y103002E01


      Text in Illustration 
      *1
      Front Glass Panel
      *2
      Center Glass Panel
      *3
      Rear Glass Panel
      -
      -
      *a
      Fully Closed Condition
      *b
      Fully Tilted Up Condition
      *c
      Fully Opened Condition
      -
      -


CONSTRUCTION


  1. SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY



    1. The sliding roof ECU uses 2 Hall ICs to detect the position of sliding roof. The sliding roof ECU and the 2 Hall ICs are integrated in the sliding roof drive gear sub-assembly.


      Y103003E01


      Text in Illustration 
      *1
      Sliding Roof Motor
      *2
      Hall IC
      *3
      Sliding Roof Control ECU
      -
      -