TIRE PRESSURE WARNING SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Tire Pressure Warning ECU
  1. Receives the data from the tire pressure warning antenna and receiver and monitors the tire pressure.
  2. When the tire pressure warning ECU detects a drop in the tire pressure, a system malfunction, or initialization mode, it outputs the respective signal to the combination meter assembly.
  3. When the tire pressure warning ECU detects a problem with the vehicle speed signal, it uses changes in the signal strength from the tire pressure warning valve and transmitter as a judgment standard. If the ECU detects any changes in the signal strength from the tire pressure warning valve and transmitter, it determines that the vehicle is being driven.
Tire Pressure Warning Valve and Transmitter
Detects the pressure and internal temperature of the tire and transmits the measured value and the ID code to the tire pressure warning antenna and receiver.
Tire Pressure Warning Antenna and Receiver
Receives the tire pressure warning valve and transmitter signal and transmits this data to the tire pressure warning ECU.
Tire Pressure Warning Reset Switch
The appropriate air pressures of the tires currently mounted on the vehicle are stored in the tire pressure warning ECU by operating the tire pressure warning reset switch.
Combination Meter Assembly
Transmits the vehicle speed signal to the tire pressure warning ECU.
Tire Pressure Warning Light
  1. Illuminates or turns on after blinking for 1 minute to warn the driver in accordance with the signal from the tire pressure warning ECU.
  2. Displays the 2-digit Diagnostic Trouble Code (DTC).

FUNCTION
  1. Warning Function

    1. The tire pressure warning ECU has 2 warning methods that are used, depending on the condition detected.

      Tire Pressure Warning Light
      Detection Condition
      Illuminate*1
      The tire pressure warning ECU has detected that a tire pressure has dropped below the threshold. The threshold varies according to the initialization value.
      Turns on after blinking for 1 minute*2
      The tire pressure warning ECU has detected a malfunction in the system.

      HINT:
      *1: If the tire pressure warning light illuminates, adjust the tire pressure.
      *2: If the tire pressure warning light turns on after blinking for 1 minute, the system is malfunctioning, and must be repaired to turn off the light.

  2. Initial Check Function

    1. After turning the power switch on (IG), the tire pressure warning ECU illuminates the tire pressure warning light for 3 seconds to check the warning light circuit.

  3. Initialization Mode Function

    1. The warning threshold is calculated from the tire pressure and memorized in the tire pressure warning ECU. Therefore, the tire pressure warning ECU should be initialized after:

      1. The tire pressure specified value changes according to vehicle weight or speed conditions or the tire pressure specified value changes as a result of a different tire size.
      2. Tire rotation when the preset tire pressure differs between the front and rear.
      3. Replacement of the tire pressure warning ECU or the tire pressure warning valve and transmitter.

    2. For initialization of the tire pressure warning ECU, refer to the Repair Manual.


CONSTRUCTION


  1. Tire Pressure Warning Valve and Transmitter

    1. The tire pressure warning valve and transmitters are integrated in the tire valves. Each tire pressure warning valve and transmitter consists of a lithium battery, sensor and transmitter.

    2. The tire pressure warning valve and transmitter directly measures tire pressure and temperature.

    3. The transmitter transmits these measured values to the tire pressure warning antenna and receiver on a frequency of 314.98 MHz.



    4. The ID code is written on the tire pressure warning valve and transmitter.


      X101792E01


      Text in Illustration 
      *1
      Tire Pressure Warning Valve and Transmitter
      *2
      Grommet
      *3
      Washer
      *4
      Nut
      *5
      Tire Valve Core
      *6
      Cap
      *7
      Lithium Battery
      *8
      Sensor and Transmitter
      *9
      ID Code (Hexadecimal 7 Digits)
      -
      -

      HINT:
      1. The lithium batteries of the tire pressure warning valve and transmitter are of a non-replaceable type. If the lithium battery is depleted, the tire pressure warning valve and transmitter must be replaced.
      2. A new tire pressure warning valve and transmitter is shipped in sleep mode to prevent the battery from depleting in storage. When the pressure in the detection portion of the tire pressure warning valve and transmitter increases or decreases by 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds, the tire pressure warning valve and transmitter automatically cancels sleep mode. Once sleep mode is canceled, the tire pressure warning valve and transmitter cannot return to sleep mode.
      3. After a tire pressure warning valve and transmitter is replaced, the ID code of the tire pressure warning valve and transmitter must be registered in the tire pressure warning ECU. To register an ID code, use the Techstream to enter the ID code that is indicated on the tire pressure warning valve and transmitter.
      4. When replacing a tire pressure warning valve and transmitter, all of the ID codes for the tire pressure warning valve and transmitters must be registered. Even if only 1 tire pressure warning valve and transmitter is replaced, the ID codes of all the tire pressure warning valve and transmitters must be registered again. Record all existing ID codes before beginning the process of entering new ID codes.
      5. Replace the grommet when the tire pressure warning valve and transmitter are being replaced to ensure the sealing performance. Note that the grommet is not reusable.
      6. For details, refer to the Repair Manual.


DIAGNOSIS
  1. To inform the driver when the tire pressure warning ECU detects a malfunction in the system, the tire pressure warning ECU will blink the tire pressure warning light for 1 minute, after which the light will stay on. It will also store Diagnostic Trouble Codes (DTCs) in memory.

  2. The DTCs can be read by connecting the Techstream to the DLC3, or by connecting the SST (09843-18040) to the TC and CG terminals of the DLC3, and observing the blinks of the tire pressure warning light. For details, refer to the Repair Manual.