DYNAMIC RADAR CRUISE CONTROL SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components in the dynamic radar cruise control system have are the following functions:

    Component
    Function
    Millimeter Wave Radar Sensor
    Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle being driven ahead, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the driving support ECU.
    Cruise Control Main Switch
    ON-OFF Button
    Turns the power to the cruise control system on and off.
    MODE Switch
    Switches the control mode, between the constant speed control mode and vehicle-to-vehicle distance control mode.
    CANCEL Switch
    A cancel signal can be output to the driving support ECU through the operation of this switch.
    +RES Switch
    The accelerate function and resuming of a preset speed can be performed by operating this switch. A signal is output to the driving support ECU when this switch is operated.
    -SET Switch
    The decelerate function and vehicle speed setting resume signals are output to the driving support ECU due to operation of this switch.
    Distance Control Switch
    While the system is in the vehicle-to-vehicle distance control mode, the driver can operate the distance control switch to select the vehicle-to-vehicle distance in 3 stages: long, middle, and short.
    Driving Support ECU
    1. Calculates the motive force required to achieve the target vehicle speed/target vehicle-to-vehicle distance based on signals from switches, sensors and ECUs and transmits motive force request signals to the power management control ECU (to accelerate the vehicle in accordance with the motive force request) and the skid control ECU (to decelerate the vehicle in accordance with the motive force request).
    2. Determines the preceding vehicle based on information from the millimeter wave radar sensor.
    3. Transmits control status display request signals, warning display request signals and diagnosis signals for the dynamic radar cruise control system.
    Power Management Control ECU
    1. Increases and decreases the motive force in accordance with the motive force request signals transmitted by the driving support ECU.
    2. Transmits the information about motive forces that are actually generated and can be generated to the driving support ECU.
    MG ECU
    Built into the inverter with converter assembly. Controls the motive force of the MG2 in accordance with signals from the power management control ECU.
    ECM
    Actuates the throttle control motor in accordance with the signals from the power management control ECU.
    Skid Control ECU
    1. While the system is operating in vehicle-to-vehicle distance control mode, the skid control ECU performs brake control in accordance with motive force request signals from the driving support ECU.
    2. Transmits signals such as a wheel speed and estimated vehicle acceleration to the driving support ECU.
    Combination Meter Assembly
    Cruise Main Indicator Light
    1. Comes on when constant speed control mode is entered.
    2. Brinks if a malfunction occurs during constant speed control mode control.
    Radar Cruise Control Indicator Light
    1. Comes on when the cruise control main switch ON-OFF button is pressed to start the cruise control system.
    2. Brinks if a malfunction occurs during vehicle-to-vehicle distance control mode control.
    Cruise SET Indicator Light
    Illuminates when the vehicle speed is set.
    Master Warning Light
    Illuminates when there is a malfunction in the system.
    Buzzer
    If the driving support ECU detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver.
    Multi-information Display
    During dynamic radar cruise control operation, the multi-information display receives signals from the driving support ECU, in order to display the system conditions.
    MG2
    Generates the motive force for the wheels.
    Throttle Control Motor
    Adjusts the throttle valve opening angle in accordance with signals from the ECM.
    Brake Actuator
    Actuates the brakes in accordance with the signals from the skid control ECU.
    Stop Light Control Relay
    Illuminates the stop light in accordance with the stop light illumination request signal from the skid control ECU.
    Skid Control Buzzer
    Sounds on receiving a signal from the skid control ECU and alerts the driver that the distance between vehicles is short.
    Speed Sensor
    Detects the wheel speed of each of 4 wheels.
    Accelerator Pedal Position Sensor
    Detects the accelerator pedal depression degree and outputs it to the power management control ECU.
    Shift Lever Position Sensor
    Detects the shift position and transmits signals to the power management control ECU.
    Steering Angle Sensor
    Detects the angle and direction of steering and transmits signals to the driving support ECU.
    Yaw Rate and Acceleration Sensor
    Detects the yaw rate of the vehicle and transmits signals to the driving support ECU.
    Stop Light Switch
    Detects the pressing of the brake pedal and transmits its signal to the driving support ECU.
    Windshield Wiper Switch
    Transmits windshield wiper switch information (HI position) to the driving support ECU.


SYSTEM CONTROL
  1. The dynamic radar cruise control system is controlled by the driving support ECU. The driving support ECU increases and decreases the vehicle speed by controlling the engine, MG2 and brake through the motive force request signals.

  2. The combination meter assembly informs the driver of the control conditions.



  3. The cruise control main switch is used for switching between the constant speed control mode and the vehicle-to-vehicle distance control mode. The mode in which the cruise control system starts is the vehicle-to-vehicle distance control mode.


    Y102739E01


FUNCTION
  1. Function List

    1. The control of the dynamic radar cruise control system varies depending on the mode:
      A: Constant Speed Control Mode
      B: Vehicle-to-vehicle Distance Control Mode

      Function
      Outline
      Mode
      A
      B
      Constant Speed Control
      Controls the motive force through the driving support ECU via the power management control ECU and skid control ECU, and adjusts the vehicle speed to the set vehicle speed.
      X
      X
      Deceleration Control
      Performs engine, MG2 and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead equals the set distance.
      -
      X
      Follow-up Control
      After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance in accordance with the vehicle speed.
      -
      X
      Acceleration Control
      Accelerates the vehicle in order to attain the set vehicle speed if the vehicle ahead or the driver's own vehicle has changed lanes.
      -
      X
      Set Control
      1. While this system fulfils the following conditions, and the cruise control main switch is moved to the -SET side and released, the driving support ECU stores the vehicle speed and maintains the vehicle constantly at that speed.
        1. ON-OFF button on the cruise control main switch is pressed.
      X
      X
      1. The vehicle is running at an approximate speed of between 50 km/h (30 mph) and 200 km/h (125 mph).
      X
      -
      1. The vehicle is running at an approximate speed of between 50 km/h (30 mph) and 170 km/h (105 mph).
      -
      X
      Low Speed Limit Control
      The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 40 km/h (25 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while running in the cruise control, the cruise control will be cancelled automatically. The set vehicle speed is kept in memory.
      X
      X
      COAST (-) Switch Control
      When the cruise control main switch is held to the -SET side, the vehicle speed and the set vehicle speed change as follows, according to the mode:
      X
      X
      1. The vehicle decelerates constantly.
      2. The set vehicle speed changes to the speed at which the switch is released.
      X
      -
      1. The set vehicle speed decreases in increments of 5 km/h or 5 mph. (Example: 103 →100 →95 km/h [mph])
      2. The vehicle will remain at the speed that the vehicle is traveling at when the COAST switch is released.
      -
      X
      Tap Down Control
      When the cruise control main switch is moved momentarily (approximately 0.6 seconds or less) to the -SET side, the vehicle speed and the set vehicle speed change as follows, according to the mode:
      X
      X
      1. The vehicle will decelerate in increments of approximately 1.6 km/h (1 mph) for each time the switch was moved.
      2. However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle was traveling at when the switch was released.
      X
      -
      1. The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the switch was moved.
      -
      X
      ACC (+) Switch Control
      When the cruise control main switch is held to the +RES side, the vehicle speed and the set vehicle speed change as follows, according to the mode:
      X
      X
      1. The vehicle will accelerate constantly.
      2. The set vehicle speed changes to the speed at which the switch is released.
      X
      -
      1. The set vehicle speed increases in increments of 5 km/h or 5 mph. (Example: 103 →105 →110 km/h [mph])
      2. The vehicle will accelerate to the speed that is set at the time the switch is released. However, only the set vehicle speed will change during follow-up control.
      -
      X
      Tap Up Control
      When the cruise control switch is moved momentarily (approximately 0.6 seconds or less) to the +RES side, the vehicle speed and the set vehicle speed change as follows:
      X
      X
      1. The vehicle will accelerate in increments of approximately 1.6 km/h (1 mph) for each time the switch was moved.
      2. However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change.
      X
      -
      1. The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the switch was moved.
      -
      X
      RES Switch Control
      If the vehicle speed is above the low speed limit, the cruise control resumes operation (when the cruise control main switch is subsequently moved to the +RES side) to reach the vehicle speed that was set at the time the driver canceled cruise control.
      X
      X
      If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set vehicle speed. At this time, the vehicle speed can be increased promptly by moving the cruise control main switch to the +RES side.
      -
      X
      Manual Cancel Control
      1. If any of the following signals are sent to the driving support ECU, the cruise control is cancelled accordingly.
        1. Stop light switch on signal (The brake pedal is depressed.)
        2. D position circuit in the shift lever position sensor off signal (The shift lever is moved from D to N or B.)
        3. CANCEL switch on signal (The cruise control main switch moved to the CANCEL side.)
        4. Cruise control main switch (ON-OFF button) off signal
        5. VSC operation
      X
      X
      Automatic Cancel Control
      When an automatic cancel signal is sent to the driving support ECU, cruise control operation is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal.
      X
      X
      Mode Switching Control
      1. The following operations switch modes:
      1. 1) The ON-OFF button on the cruise control main switch is on (starts in the vehicle-to-vehicle distance control mode).
      2. 2) The cruise control main switch is held to the MODE side (approximately 1 second or more). If the switch is moved to any other side before switching modes, switch the cruise control system off; then, perform steps 1) and 2) again.
      X
      X

      1. X: Available
      2. -: Not Available



  2. Constant Speed Control

    1. The driving support ECU compares the actual vehicle speed (wheel speed signal from the skid control ECU) with the set vehicle speed under constant speed control in each control mode. When the actual vehicle speed differs from the set vehicle speed, the driving support ECU calculates the motive force required to achieve the set vehicle speed and transmits motive force request signals to the power management control ECU, thus controlling the motive force optimally and adjusting the actual vehicle speed to the set vehicle speed.



    2. In vehicle-to-vehicle distance control mode, the driving support ECU performs deceleration control or follow-up control or acceleration control based on the information about the vehicle ahead transmitted from the millimeter wave radar sensor.


      Y102740E01



  3. Deceleration Control

    1. The driving support ECU calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor, and transmits a motive force request signal to the power management control ECU and the skid control ECU. Upon receiving this signal, these ECUs control the motive force and decelerate the vehicle.



    2. This control is not performed in the presence of a parked vehicle or object, or below the settable vehicle speed range.


      Y102742E01

    3. If the driving support ECU determines that further deceleration is necessary, it transmits a motive force request signal to the skid control ECU. Upon receiving this signal, the skid control ECU then activates the brake actuator to apply the brakes.



    4. At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop light control relay, in order to inform anyone who might be following the vehicle.


      Y102743E01



    5. If the vehicle is not decelerating adequately, the skid control ECU sounds the skid control buzzer based on the request signal from the driving support ECU to urge the driver to depress the brake pedal.


      Y102744E01



  4. Follow-up Control

    1. After performing deceleration control, the driving support ECU transmits a motive force request signal to the power management control ECU and the skid control ECU so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving this signal, these ECUs control the motive force in order to perform follow-up control.



    2. 3 stages (long, middle, and short) of vehicle-to-vehicle distance can be selected by operating the distance control switch.


      Y102745E01



  5. Acceleration Control



    1. If the driving support ECU detects that either the vehicle ahead or own vehicle has changed lanes, a motive force request signal is transmitted to the power management control ECU in order to attain the set vehicle speed. Upon receiving this signal, the power management control ECU controls the motive force of the engine and MG2 in order to perform acceleration control.


      Y102746E01

  6. Automatic Cancel Control

    1. If any of the conditions listed below occur while the vehicle is being driven using cruise control, the cruise control will be canceled. Then, the following warning items will appear for the driver.

      Constant Speed Control Mode: 
      Description of Malfunction
      Warning
      Multi-information Display
      Y100442
      Buzzer
      Y100439
      1. If the condition listed below occur, the driving support ECU clears the set vehicle speed and cancels the cruise control.
        1. Millimeter wave radar sensor and driving support ECU region code mismatch is detected.
      1. The cruise control is prohibited until the conditions are remedied or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control main switch.
      CHECK CRUISE CONTROL SYSTEM
      Illuminates
      Sounds Once
      Blinks
      1. If any of the conditions listed below occur, the driving support ECU clears the set vehicle speed and cancels the cruise control.
        1. Malfunction of the vehicle speed signal
        2. An open or short circuit in the stop light switch
        3. Malfunction in the hybrid system
      1. The cruise control is prohibited until the power switch is turned on again.
      CHECK CRUISE CONTROL SYSTEM
      Illuminates
      Sounds Once
      Blinks
      1. If the condition listed below occurs, the driving support ECU clears the set vehicle speed and cancels the cruise control.
        1. The vehicle speed drops more than 16 km/h (10 mph) below the set vehicle speed.
      -
      -
      -
      -
      1. If the condition listed below occurs, the driving support ECU cancels the cruise control while retaining the set vehicle speed in its memory.
        1. The vehicle speed drops below low speed limit (approximately 40 km/h [25 mph]).
      -
      -
      -
      -

      Vehicle-to-Vehicle Distance Control Mode: 
      Description of Malfunction
      Warning
      Multi-information Display
      Y100442
      Buzzer
      Y101992
      1. If the condition listed below occur, the driving support ECU clears the set vehicle speed and cancels the cruise control.
        1. Millimeter wave radar sensor and driving support ECU region code mismatch is detected.
      1. The cruise control is prohibited until the conditions are remedied or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control main switch.
      CHECK CRUISE CONTROL SYSTEM
      Illuminates
      Sounds Once
      Blinks
      1. If any of the conditions listed below occur, the driving support ECU clears the set vehicle speed and cancels the cruise control.
        1. Malfunction of the vehicle speed signal
        2. An open or short circuit in the stop light switch
        3. Malfunction in the hybrid system
        4. Malfunction of the millimeter wave radar sensor.
        5. Displacement of the axis of the millimeter wave radar sensor.
        6. Malfunction in the dynamic radar cruise control system other than those given above.
      1. The cruise control is prohibited until the power switch is turned on again.
      CHECK CRUISE CONTROL SYSTEM
      Illuminates
      Sounds Once
      Blinks
      1. If the condition listed below occurs, the driving support ECU cancels the cruise control while retaining the set vehicle speed in its memory.
        1. The millimeter wave radar sensor is dirty.
      1. The cruise control is prohibited until the conditions are remedied or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control main switch.
      CLEAN RADAR SENSOR
      Illuminates
      Sounds Once
      Blinks
      1. If any of the conditions listed below occur, the driving support ECU cancels the cruise control while retaining the set vehicle speed in its memory.
        1. The wipers operate at HI speed.
        2. The measurement becomes extremely unstable due to poor weather conditions.
      1. The cruise control is prohibited until the conditions are remedied or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control main switch.
      CRUISE CONTROL NOT AVAILABLE DUE TO ADVERSE CONDITIONS
      Illuminates
      Sounds Once
      Blinks
      1. If the condition listed below occurs, the driving support ECU cancels the cruise control while retaining the set vehicle speed in its memory.
        1. The vehicle speed drops below low speed limit (approximately 40 km/h [25 mph]).
      -
      -
      -
      -


CONSTRUCTION


  1. Cruise Control Main Switch

    1. The cruise control main switch consists of the ON-OFF button, +RES, MODE, -SET and CANCEL switches. The +RES, MODE, -SET and CANCEL switches are operated by moving the lever in the 4 directions indicated.



    2. The cruise control main switch is an automatic reset (normally open) type that turns on only when the switch is being operated and turns off as soon as the driver releases the switch. Furthermore, the functions of the control switch are active only when the cruise control system has been turned on using the ON-OFF button on the cruise control main switch.


      Y114993E01


      Text in Illustration 
      *1
      Cruise Control Main Switch
      -
      -
      *a
      ON-OFF Button
      *b
      +RES Switch
      *c
      MODE Switch
      *d
      -SET Switch
      *e
      CANCEL Switch
      -
      -



  2. Distance Control Switch



    1. While the vehicle is being driven in vehicle-to-vehicle distance control mode, the vehicle-to-vehicle distance setting can be changed as follows each time the distance control switch is pressed; long → middle → short.


      Y114994E01


      Text in Illustration 
      *1
      Distance Control Switch
      -
      -

    2. If the power switch is turned off and back to on (IG), the system will default to "long".

    3. The vehicle-to-vehicle distance is set as follows:

      Mode
      Vehicle-to-Vehicle Distance*
      Long
      Approximately 50 m (160 ft.)
      Middle
      Approximately 40 m (130 ft.)
      Short
      Approximately 30 m (100 ft.)

      HINT:
      *: While driving at a vehicle speed of 80 km/h (50 mph).



  3. Millimeter Wave Radar Sensor

    1. The millimeter wave radar sensor consists of a millimeter wave radar circuit, signal processing circuit, and CPU.

    2. The millimeter wave radar outputs waves when the vehicle speed is above 0 km/h (0 mph), and not when the vehicle speed is at 0 km/h (0 mph). The millimeter wave radar uses frequencies in the 76 GHz band.

    3. The reception antennas receive the millimeter wave radar waves that have been reflected.



    4. The signal processing circuit detects the distance, relative speed, and the direction of the object by generating millimeter wave radar waves and calculating the signals received by the reception antennas. Then, it transmits this information to the driving support ECU.


      Y102749E01


      Text in Illustration 
      *1
      Millimeter Wave Radar Sensor
      -
      -
      *a
      Detection Distance
      *b
      Horizontal Angle
      *c
      Vertical Angle
      -
      -



    5. The distance to the object, azimuth, and relative speed are calculated from the information that is provided by the reflection millimeter wave radar as described below.

      Item
      Calculation Method
      Distance
      Calculated from the length of time that has elapsed from the time the waves of the millimeter wave radar have been emitted, until the waves reflected by the millimeter wave radar are received. The detection distance is approximately 150 m (490 ft.).
      Azimuth
      Calculated from the angle of the waves reflected by the millimeter wave radar that have been received. Detection angle has a horizontal angle of approximately 20° and a vertical angle of approximately 8°.
      Relative Speed
      Calculated by utilizing the changes (Doppler effect*) that occur in the frequencies of the reflected millimeter wave radar waves.

      HINT:
      *: The Doppler effect causes the observer to perceive the radio waves emitted by a moving object to be of higher frequencies as it approaches, and to be of lower frequencies at it recedes. This phenomenon is created because when an object is located far away, the radio waves are perceived at higher frequencies than those of the radio source.


      Y102750E04

      HINT:
      An SST is used if radar axis adjustment is needed. For details, refer to the Repair Manual.


OPERATION
  1. Combination Meter Assembly

    1. The combination meter assembly provides a master warning light, cruise main indicator light, radar cruise control indicator light, cruise SET indicator light, buzzer, and multi-information display to warn and indicate in the dynamic radar cruise control system.

    2. The multi-information display displays the set vehicle speed, vehicle ahead mark, and warning message.

    3. Examples are shown below for the illumination or display of each indicator light, warning light or multi-information display.

      Mode
      Condition
      Multi-information Display
      Y100439
      Y101992
      Y100440
      Y100442
      Buzzer
      Constant Speed Control
      Being Controlled
      Y102751
      Illuminates
      -
      Illuminates
      -
      -
      Vehicle-to-Vehicle Distance Control
      Set Standby
      Y102752
      -
      Illuminates
      -
      -
      -
      Under Constant Speed Control (No Vehicle Ahead, Short)
      Y102753
      -
      Illuminates
      Illuminates
      -
      -
      Under Follow-up Control (Vehicle Ahead, Middle)
      Y102754
      -
      Illuminates
      Illuminates
      -
      -
      Deceleration Control/Vehicle Approach Warning (Vehicle Ahead, Long)
      Y102755
      -
      Illuminates
      Illuminates
      -
      Skid Control Buzzer Sounds Continuously
      The vehicles in the display are highlighted at 0.5-second intervals.
      System Failure
      Millimeter Wave Radar Sensor is Dirty.
      Y102756
      -
      Blinks
      -
      Illuminates
      Sounds Once
      Poor Weather Condition
      Y102757
      -
      Blinks
      -
      Illuminates
      Sounds Once
      System Check
      Y102758
      Blinks*1
      Blinks*2
      -
      Illuminates
      Sounds Once
      Beam Axis Adjustment
      Y102759
      -
      Illuminates
      -
      -
      Skid Control Buzzer Sounds Once

      HINT:
      *1: Constant speed control mode
      *2: Vehicle-to-vehicle distance control mode


DIAGNOSIS
  1. If a malfunction occurs in the dynamic radar cruise control system, during cruise control operation, the driving support ECU cancels the cruise control and blinks the cruise main indicator light or radar cruise control indicator light to inform the driver of the malfunction. At the same time, the malfunction is stored in memory as a Diagnostic Trouble Code (DTC).

  2. The DTC can be read when the Techstream is connected to DLC3. The Techstream can be used to read the 5-digit codes. For details, refer to the Repair Manual.